Hi everyone, Not long time ago started to see such problem. I'm using the default ASA firewall config (inside is 192.168.42.253/24) and setup the FirePower module to use 192.168.42.203/24. I can ping the FirePower module from my PC and from the ASA'...
Forum Posts
I have a scenario where traffic from Site A to Site B takes place via NAT... now the requirement is to put this NATted traffic in a VPN Tunnel created in Cisco ASA/Firepower. When i try to create site to site vpn tunnels it gives an option to exempt ...
Hi, after update the ASA image, I've noticed the following messages/warnings after reboot:(I use the following ASA image: asa984-15-lfbff-k8.SPA)Configuring network interfaces... done.Populating dev cachedosfsck 2.11, 12 Mar 2005, FAT32, LFNThere are...
HiThis is probably a really simple question ! - I have a Cisco 5545 which i'm accessing via the cli which is already fully configured.I recently entered a 'command show running-config | b crypto' so I could take a look at specific crypto configuratio...
I need to take CCNP 300-206 before February 24 and take the core exam after February 24 2020 is there any prerequisite i have to take before February 24 and also according to the new policy i need to have Cisco Certified Specialist - Web Content Sec...
Hello All,We have created site to site tunnel between ASA5512 and RV340.On primary tunnel we are able to access the resource where as for failover/secondary tunnel we cannot access the resource. Any assistance would be of great help.
Hi everyone, I am using an ASA 4110 cluster with 4 devices in multi-context mode and ASDM 7.8 (2). Is there a way to show the log from all devices in the cluster in Real-Time Log Viewer? Now I can see the log from only one device in the cluster.
Resolved! FMC classic license for managed devices
hello guys,,, need your help I have installed FMCv 6.5 version to manage 2 ASA 5516 with firepower services in (active/active) multi-context mode, I added the classic license as shown in the screenshot but the license didn't appear when I want to add...
Hello,I have a query regarding IPsec VPN setup. We are configuring IPsec VPN between two nodes, details are given below - Node A - Check Point Firewall Node B - Cisco Firepower Threat DefenseNode A - VPN Initiator ...
Hi all, Apologies if this has been asked before. still extremely new with packet tracer and cisco etc. I am practicing connecting too remote networks and then adding a cisco asa 5505. i have managed to allow icmp requests through the firewall when th...
We have parched cisco firewall ASA5508-FTD-K9 and Security Context License ASA5500-SC-5. Below is my query: Is it possible to push context license in ASA5508-FTD-K9? If is possible send me Configuration Procedure detailsIf is not possible to how c...
I have a cisco 1900 router connected to ISP with Static IP address and the router has been configured to act as DHCP to the 2 switches behind it and all hosts connected to the switches are browsing. Now, i want the ASA to be behind the router and al...
Hi, I want to allow internet access for host within 172.12.0.0/16 network to access internet. I have created source nat and ACL to allow traffic but still users cant access internet. please find below config i have done and guide for any missing stuf...
I have come across a conflict situation. And given the limitation that we cannot apply an NAT to remote environment. Tunnel 1Local Firewall IP : x.x.x.xPeer Firewall IP : y.y.y.yLocal Subnet : 10.252.100.0/24Remote Subnet : 192.168.100.0/24 Tunnel 2L...
Hello, I have created my Realm and its enabled -I have added the directory server from the Active Directory domain as an agent and its reporting as working ok. I have the cisco agent installed on the agent server I have created the identity policy ...
