Dears, I am planning to implement Fortinet Sand boxing solution and i have a ASA with firepower services, will this solution will work ??? the file which will be send to fortinet sandboxing by ASA will be recognized??? Please confirm.
HiI have this on my Cisco ASR 1001-X particulary for ipsec License State: Active, Not in Use, EULA not accepted Can anyone explain what it means please
I have a vendor that I need to set up a site to site vpn with and they want me to use public IPs in the encryption domain. Can anyone explain why they would want to do this or if it offers any security benefits or weaknesses?
I would like to deploy FMC HA across two data centers. There are two data centers. Each data center has- 1 FMC- 1 pair of FTD HA Note that please find the attached network diagram. Because there are existing firewalls in between two data centers,does...
I have Cisco ASA5545-MB running in Active-Active Failover in DC. I have got task to upgrade this ASA to work with Firepower Services and install IPS on it. There are some challenges which I would like to overcome:-1) Do I need to remove the IPS legac...
Hello, Monitoring Team has reported that the Firepower Devices in the environment are reporting the following alert : "Multicast routing group status is not normal" Need help in understanding what might be causing this alert and how to remedy it .Tha...
Hello, I need help in understanding the audit trail in Cisco ASA.How can i cross check if audit logs are being generated in ASA and are being forwarded to syslog server correctly
Have a basic setup w/ a e-lan circuit that terminates on a subinterface of the ASA w/ a /29 defined. The ASA and the remote firewall each have an ip in the /29 and ping the far end device to see if that link is good. On the ASA i have the following...
Hello! Friends! I need your advice. I do not have ideas. May be you can help me.So a have two offices (office 1 and office 2), for it connecting i used cisco asa 5510 and VPN between it. (site2site)office 1 - 192.168.101.0/24 office 2 - 192.168.104.0...
Hello! I've run to the situation, where i configured my ASA completely and left the licencing for the last step and apparently i could not licence it because of non-existent FirePower Services module in ASDM, where i'm supposed to obtain the licence ...
Hello All,i am trying to monitor below ASA firewalls and want to know the oid which will give the disk utilization status when polled. which MIB file will have the SNMP oid for this.ASA5506-XCISCO ASA 5508Cisco ASA 5525Cisco ASA 5545 regards,Prasad
HI All,We have ASA 5516x with firepower in HA at two different location and we are using virtual FMC at branch level. Now our requirement is to move FMC in DC(other location) and add both location firepower.I have some query to perform this activity:...
Hi,How to check Standby serian no (Activie and standby) from Primary firewall console ?Without connect console to secondary fireall ? how to check this from primary firewall ?thanks in advance ?
So if you have a syslog server on inside network/interface of ASA, and have an IDS/IPS on Outside of ASA you want to send its logs to the server, you should allow the mgmt IP address of the IDS/IPS if it is setup for syslog forwarding via its mgmt in...
Good Day,Im currently having an issue where i have my sub interfaces configurated on my router. I also have an ASA5508 that i am using to control traffic. The asa can block traffic between the outside(isp) and inside(internal vlans) with no problem. ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
