03-09-2012 10:30 PM - edited 03-11-2019 03:40 PM
I having problem when I try to change interface Ethernet0/1 to switchport access vlan 1, but when I try to monitor it using the run command it does not appear. What do I need to do to make it work? And also what is my next step so that I could access ASDM on my web browser? The ios I use is asa843-k8.bin and asdm-647.bin on ASA 5505.
: Saved
:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
!
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.36 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:ec3006dc4cab42f81d133b398ddb0b6c
: end
03-10-2012 05:40 AM
is k9 active ? Do you connect to Asa from vista/win7?
Sent from Cisco Technical Support iPad App
03-10-2012 05:41 AM
its been a while since I played with 5505, but I think all the interfaces are part of vlan 1 by default..hence it is not shown in the running config.
try sh run all interface
for the HTTP the following commands are already there.
http server enable
http 192.168.1.0 255.255.255.0 inside
what you need is the following
username ADMIN password WHATEVER priv 15
aaa authentication http console LOCAL
Please mark complete and also rate if my reply was helpful to you.
Thank you.
03-10-2012 05:45 AM
If k9 not active and vista/win7 used to connect to Asa via https , Asa will.drop connection because DES not supported by default in vista/win7 SSL ciphers
Sent from Cisco Technical Support iPad App
03-27-2013 07:42 PM
Thank you so much for your reply.
Yes, my OS is Win 7
How can I active k9
So what is your recommendation
03-10-2012 09:40 AM
I'm using Win7. Could someone show me their outpu on asa 5505 so that I could compare it to mine? Thanks
This is my output:
ciscoasa# show run
: Saved
:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
!
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server asdm protocol tacacs+
accounting-mode simultaneous
user-identity default-domain LOCAL
aaa authentication http console LOCAL
aaa authentication secure-http-client
http server enable
http 192.168.10.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.10.5-192.168.10.36 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username ADMIN password xlaEBzC9eIymxW7v encrypted privilege 15
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
call-home reporting anonymous prompt 2
Cryptochecksum:91ec6c81a5b77bb7da9743edafe60cc0
: end
Below is the command that I ran but the show run command doesn't show the changes that I want. Please help me on this issue.
ciscoasa# conf t
ciscoasa(config)# int e
ciscoasa(config)# int ethernet 0/1
ciscoasa(config-if)# no shut
ciscoasa(config-if)# switch
ciscoasa(config-if)# switchport access vlan 1
ciscoasa(config-if)# exit
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
03-10-2012 11:20 AM
Hi
As noted on this thread, vlan1 is the default vlan so you will not see this in the running config.
Regards Craig
03-10-2012 04:03 PM
have you tried my above recomendation?
also have you verified that your image is K9... a show ver would help
03-11-2012 08:55 PM
I used asdm-647.bin. What else do I need to do to make it work? When I used Cisco ASDM Launcher it pop up as Unable to launch device from 192.168.1.1.
ciscoasa# show version
Cisco Adaptive Security Appliance Software Version 8.4(3)
Device Manager Version 6.4(7)
Compiled on Fri 06-Jan-12 10:24 by builders
System image file is "disk0:/asa843-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 48 mins 49 secs
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xfff00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode : CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
Number of accelerators: 1
0: Int: Internal-Data0/0 : address is 001b.5446.d78a, irq 11
1: Ext: Ethernet0/0 : address is 001b.5446.d782, irq 255
2: Ext: Ethernet0/1 : address is 001b.5446.d783, irq 255
3: Ext: Ethernet0/2 : address is 001b.5446.d784, irq 255
4: Ext: Ethernet0/3 : address is 001b.5446.d785, irq 255
5: Ext: Ethernet0/4 : address is 001b.5446.d786, irq 255
6: Ext: Ethernet0/5 : address is 001b.5446.d787, irq 255
7: Ext: Ethernet0/6 : address is 001b.5446.d788, irq 255
8: Ext: Ethernet0/7 : address is 001b.5446.d789, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
The Running Activation Key is not valid, using default settings:
Licensed features for this platform:
Maximum Physical Interfaces : 8 perpetual
VLANs : 3 DMZ Restricted
Dual ISPs : Disabled perpetual
VLAN Trunk Ports : 0 perpetual
Inside Hosts : 10 perpetual
Failover : Disabled perpetual
VPN-DES : Enabled perpetual
VPN-3DES-AES : Disabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 10 perpetual
Total VPN Peers : 12 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
This platform has a Base license.
Serial Number: JMX1116Z0TP
Running Permanent Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
Configuration register is 0x1
Configuration last modified by enable_15 at 01:09:27.579 UTC Mon Mar 12 2012d
03-27-2013 10:59 PM
Hello Tho Vo,
As already explained all ports that are part of vlan 1 are assigned to the default vlan so no matter how many times you run the command show run you will not see it, Although you can run show run interface x/x and you should see the configuration there
Regarding the HTTPS problem you could get the 3DES/AES license for free.
Go to the following link and do it so you can have this:
https://tools.cisco.com/SWIFT/LicensingUI/loadDemoLicensee?FormId=139
Afterwards add the command
ssl encryption aes128-sha1 3des-sha1 aes256-sha1
And you should be good to go
Remember to rate all of the helpful posts
10-02-2014 06:01 AM
I for the life of me couldn't figure out why I couldn't get my ASDM to load with all the proper configs and license.
The command: ssl encryption aes128-sha1 3des-sha1 aes256-sha1
is the one that you need to use to get ASDM up a running through web. Thanks for this.
03-11-2012 09:03 PM
VPN-3DES-AES : Disabled perpetual
you can't because 3des is disabled. browser doesnt support des. you can check ssl handshake and you will see supported ciphers on both side.
solution:
1) connect from win xp (vista and win 7 doesnt support des on ssl)
2) install ASDM from cisco site (from installer) and connect to device
3) connect from console (com port)
also you can't use strong encryption with VPN, ssh2. iphone\ipad will not work. anyconnect will work from win xp
03-27-2013 07:35 PM
ciscoasa(config)# aaa authentication http console local
ERROR: aaa-server group local does not exist
Usage: [no] aaa mac-exempt match
[no] aaa authentication secure-http-client
[no] aaa authentication listener http|https
[no] aaa authentication|authorization|accounting include|exclude
[no] aaa authentication serial|telnet|ssh|http|enable console
[no] aaa accounting telnet|ssh|serial|enable console
[no] aaa authentication|authorization|accounting match
[no] aaa authorization command {LOCAL |
[no] aaa accounting command {privilege
[no] aaa proxy-limit
[no] aaa local authentication attempts max-fail
clear configure aaa
clear aaa local user {fail-attempts|lockout} {all | username
show running-config [all] aaa [authentication|authorization|accounting
|max-exempt|proxy-limit]
show aaa local user [lockout]
ciscoasa(config)# aaa authentication http console local
ERROR: aaa-server group local does not exist
Usage: [no] aaa mac-exempt match
[no] aaa authentication secure-http-client
[no] aaa authentication listener http|https
[no] aaa authentication|authorization|accounting include|exclude
[no] aaa authentication serial|telnet|ssh|http|enable console
[no] aaa accounting telnet|ssh|serial|enable console
[no] aaa authentication|authorization|accounting match
[no] aaa authorization command {LOCAL |
[no] aaa accounting command {privilege
[no] aaa proxy-limit
[no] aaa local authentication attempts max-fail
clear configure aaa
clear aaa local user {fail-attempts|lockout} {all | username
show running-config [all] aaa [authentication|authorization|accounting
|max-exempt|proxy-limit]
show aaa local user [lockout]
03-28-2013 07:28 AM
astonishing as it may seem, the "LOCAL" keyword is case-sensitive in:
aaa authentication http console LOCAL
Try it in uppercase.
-- Jim Leinweber, WI State Lab of Hygiene
03-13-2012 11:40 AM
As stated, the default VLAN1 will not show up on the port assignement part of the runtime config display. I did note you will need to make a default route to allow hosts on private lans or dmzs to reach the internet.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide