FXS DID Card Not Booting

hamid khan · ‎03-01-2015

Hi All,

I have two routers 2821 and 2811.

I have four FXS card installed on my 2821 Router.

I want to remove any of these FXS card and install on 2811.

As i do so i-e Remove one of FXS card from 2821 Router and put it in 2811 there is Yellow/orange constant light on all four ports.

Need Help in this regards.

Aman Soi · ‎03-01-2015

Hi Hamid,

Do u have DSP instaled on 2811?

can u share show inventory /show diag from 2811 router?

what is the exact model of FXS card u are using?

regds,

aman

hamid khan · ‎03-01-2015

First of all Thanks to You Aman for giving your time.

well below is the output shown by show diag.

2811#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.3.3
EEPROM contents at hardware discovery:
PCB Serial Number : FOC13442MVC
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-06
Board Revision : A0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20091102
Chassis Serial Number : FHK1346F30S
Chassis MAC Address : 0026.99cf.b038
MAC Address block size : 24
CLEI Code : COMEF00ARA
Product (FRU) Number : CISCO2811
Part Number : 73-10258-06
Version Identifier : V07
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 33 34 34 32 4D 56 43 40
0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 06 42 41 30
0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00
0x30: 09 87 83 01 32 90 DE C2 8B 46 48 4B 31 33 34 36
0x40: 46 33 30 53 C3 06 00 26 99 CF B0 38 43 00 18 C6
0x50: 8A 43 4F 4D 45 46 30 30 41 52 41 CB 8F 43 49 53
0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
0x70: 06 89 56 30 37 20 D9 02 40 C1 FF FF FF FF FF FF

Slot 1:
NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-25009-01
Board Revision : B0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : FOC11456048
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : NME-16ES-1G-P
Version Identifier : V01
Base MAC Address : 001e.4a98.0080
MAC Address block size : 128
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 04 A2 41 01 00 C0 46 03 20 00 61 B1 01
0x10: 42 42 30 80 00 00 00 00 02 03 C1 8B 46 4F 43 31
0x20: 31 34 35 36 30 34 38 03 00 81 00 00 00 00 04 00
0x30: CB 8E 4E 4D 45 2D 31 36 45 53 2D 31 47 2D 50 20
0x40: 89 56 30 31 00 D9 02 40 C1 CF 06 00 1E 4A 98 00
0x50: 80 43 00 80 FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

and i am not sure about FXS card exact model.

its say VIC 4FXS/DID

Aman Soi · ‎03-01-2015

Hi Hamid,

the output does not show any PVDM/DSP installed on it.

You need to have that.

Secondly, for the exact model , u can get from the working 2821 router.

regds,

aman

hamid khan · ‎03-02-2015

Aman can you help me in installing PVD/DSP????

Aman Soi · ‎03-02-2015

Hamid,you can refer the link .

http://www.cisco.com/c/en/us/td/docs/routers/access/2800/hardware/installation/guide/hw/10_hw.html#wp1029576

Installing and Removing PVDMs

Cisco 2801 and Cisco 2811 routers hold up to two Cisco packet voice data modules, version 2 (PVDM2) to support enhanced versions of digital signal processors (DSPs). Cisco 2821 and Cisco 2851 routers hold up to three PVDM-IIs. If only one is PVDM installed, it must be located in the PVDM 0 connector

regds,

aman

hamid khan · ‎03-02-2015

how can i check the status of PVDM installed???

Aman Soi · ‎03-02-2015

I have attached the show diag which shows PVDM installed.

You can also refer link .Table 6 shows LED status on Rear of chassis for any PVDM if installed.

http://www.cisco.com/c/en/us/td/docs/routers/access/2800/hardware/installation/guide/hw/01_hw.html

regds,

aman