10-26-2001 09:44 AM - edited 03-12-2019 01:03 PM
Hi,
I am unable to place an internation PSTN call through the gateway whereas local and national call works fine. Call is rejected by the PSTN.
Is there any timer issue ?
IOS version is 12.2(4.2) with CCM 3.1(2c)
Gateway conf :
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729r8
!
!
interface BRI1/0
no ip address
isdn switch-type basic-net3
isdn incoming-voice voice
isdn sending-complete
!
!
voice-port 1/0/0
cptone FR
description *** FAX ***
!
voice-port 1/0/1
cptone FR
description *** Repondeur ***
!
voice-port 1/1/0
compand-type a-law
cptone FR
description *** Connexion FT - ISDN ***
!
dial-peer voice 20 pots
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 1/1/0
!
dial-peer voice 30 pots
destination-pattern 6014
port 1/0/0
!
dial-peer voice 40 voip
destination-pattern 6...
progress_ind setup enable 3
voice-class codec 1
session target ipv4:192.168.3.2
dtmf-relay h245-alphanumeric
!
dial-peer voice 31 pots
destination-pattern 6013
port 1/0/1
!
**************
debug isdn q931 trace :
06:31:58: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 64 changed to up
*Mar 1 06:31:58.414: ISDN BR1/0: TX -> SETUP pd = 8 callref = 0x18
*Mar 1 06:31:58.414: Bearer Capability i = 0x8090A3
*Mar 1 06:31:58.418: Channel ID i = 0x83
*Mar 1 06:31:58.418: Calling Party Number i = 0x00, 0x80, '6082', Plan:Unknown, Type:Unknown
*Mar 1 06:31:58.422: Called Party Number i = 0x80, '0033<my_phone_number>', Plan:Unknown, Type:Unknown
*Mar 1 06:31:58.426: Sending Complete
*Mar 1 06:31:58.678: ISDN BR1/0: RX <- CALL_PROC pd = 8 callref = 0x98
*Mar 1 06:31:58.678: Channel ID i = 0x89
*Mar 1 06:31:58.766: ISDN BR1/0: RX <- DISCONNECT pd = 8 callref = 0x98
*Mar 1 06:31:58.766: Cause i = 0x8798 - Unknown cause value
*Mar 1 06:31:58.778: ISDN BR1/0: TX -> RELEASE pd = 8 callref = 0x18
*Mar 1 06:31:58.778: Cause i = 0x8098 - Unknown cause value
*Mar 1 06:31:58.854: ISDN BR1/0: RX <- RELEASE_COMP pd = 8 callref = 0x98
*********************
Any idea ?
Marc DERRIENNIC
Technical Account Manager
10-26-2001 11:10 AM
I had the same problem, it is a IOS Problem use 12.2.1 or 12.2.5a
Regards Philipp
10-27-2001 03:12 AM
I tried 12.2.1 and 12.2.1c without success.
I didn't found 12.2.5a on the CCO, can you tell me where to find it ?
Best regards,
Marc
10-26-2001 10:20 PM
I see in your debug:
Called Party Number i = 0x80, '0033'
Is 0033 a complete number? I would expect that it's not. Can you try to remove the isdn sending-complete command, because you are sending 0033 and the telco is not going to wait for any more digits because you are sending the Sending Complete IE in the SETUP message.
Also, what is the route pattern that you have configured in CallManager, both for local/national calls as well as for the international calls?
10-27-2001 02:19 AM
No 0033 is not the complete number, I just hide the 7 last numbers. 00 is for international calls in France and 33 is the international France code. I must have tell you this, sorry.
national route pattern : 0.XXXXXXXXXX
international route pattern : 0.00!
this to avoid inter digit timeout for national calls.
Marc
10-27-2001 09:28 PM
Now I am a little confused. Are you saying that in the debug isdn q931 that the entire number was actually sent, not just 0033, and you deleted the number out when you posted your debug?
10-28-2001 10:04 AM
Yes, that's it, I put an explanation that was stripped because confusing with an HTML tag...
In the debug, the entire and correct number is sent
I already had a problem like this : I was able to call people connect with ISDN to the PSTN but not home user who used an analog connection. It was an IOS bug in v12.2.3 (timer pb). With 12.2.4 this feature works but still not international calls, even with a csim start command !
Marc
10-28-2001 11:43 AM
Hi,
We had some weird problems on a PRI (call to cell-phone ended up in singapore), this solved the problem (on the serial int);
isdn map address . plan unknown type unknown
You can try this on your BRI (if you can do this on a BRI, I am not sure)
You never now...... :-)
Sascha
10-30-2001 08:59 PM
We did have this same problem and it ended up being a timer issue. The problem happened more frequently on international calls to cell phones because they take longer to connect. The two items that corrected the problem for us were:
1. On your gateway, set the call type to unknown in stead of call manager.
2. In your router, on the interface for your PRI line (ex. 2/0:23) add the entry "ISDN T310 50000"
10-31-2001 08:09 PM
Guys,
Yep the last guy to post, I think had the right idea. Below is what I did to fix a similar problem.
*configure the T310 timer in the CallManager Service Parameters to 60s
(it is prob configured to 10s)
*configure the T310 timer on the Gateway as described in the following
URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft
/121limit/121x/121xi/121xi_3/dth323pi.htm#xtocid2003913
Alan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide