Hi,
I appreciate your prompt reply.I am on a testing stage right now.But would be a upgrading to CCM 4.0 soon.
Configuration on Cisco 3640 gateway using MGCP with 2fxs & 2fxo ports:
Router(config)#host R3640A
R3640A(config)#int e0/0
R3640A(config-if)#ip address 10.4.2.254 255.255.255.0
R3640A(config-if)#no shut
R3640A(config-if)#exit
R3640A(config)#mgcp
R3640A(config)#mgcp call-agent 10.4.2.10
/* 10.4.2.10 /24 is an ip address of CCM 3.1 */
R3640A(config)#mgcp dtmf-relay voip codec all mode out-of-band
R3640A(config)#ccm-manager mgcp
R3640A(config)#dial-peer voice 1 pots
R3640A(config)#application MGCPAPP
R3640A(config)#port 3/0/0 /*FXS ports*/
R3640A(config)#dial-peer voice 2 pots
R3640A(config)#application MGCPAPP
R3640A(config)#port 3/0/1 /*FXS ports*/
R3640A(config)#dial-peer voice 3 pots
R3640A(config)#application MGCPAPP
R3640A(config)#port 3/1/0 /*FXO ports*/
R3640A(config)#dial-peer voice 4 pots
R3640A(config)#application MGCPAPP
R3640A(config)#port 3/1/1 /*FXO ports*/
R3640A(config)#voice-port 3/0/0
R3640A(config)#no shut
Both ports are in service /*FXS ports*/
R3640A(config)#voice-port 3/1/0
R3640A(config)#no shut
Both ports are in service /*FXO ports*/
Configuration on CCM3.1 for FXS/FXO ports using MGCP:
Device>Add a New Device>Gateway
Under Add a new gateway:
1.Gateway Type: cisco 3640(in my case)
2.Device Protocol:"not required for mgcp"
Under MGCP configuration:
1.MGCP Domain Name: R3640A
2.Description: 3640 gateway
3.Cisco CallManager Group: default
4.Installed VICs
a. module in slot 0-none
b. module in slot 1-none
c. module in slot 2-none
d. module in slot 3-(NM-2V)
5.Product specification configuration
a. Global ISDN switch type -4ESS
b. Switchback Timing-graceful
c. switchback uptime-delay(min)-10
d. switchback schedule(hh:mm)-12:00
Configured FXS ports:
1.Module in slot3-NM-2V
a. sub-unit 0 -VIC-2FXS 3/0/0 3/0/1
b. sub-unit 1 -VIC-2FXO 3/1/0 3/1/1
2 Then i hit "3/0/0"
a. Gateway Information
- Description: AALN/S3/SU1/0@R3640A
- Device pool: default
- Calling search space: none
- Media resource group list: none
- Network hold audio source: none
- User hold audio source:none
- Location:none
b.Port Information
- Prefix DN:
- Num Digits:0
- Expected Digits :0
3.Directory number configuration in fxs
a.Directory Number
- directory number:2001 in one fxs and 2002 in
another fxs (3/0/1)
- partition:none
b.Directory Number Settings
- voice mail box: varies if DN is 2001, then it
is 2001,and so on.
- calling search space:none
- user hold audio source:none
- network hold audio source:none
- call waiting:defaut
- auto answer:not available
c. Call Forward And Pickup Settings
voice mail destination calling search space
1.Forward all none
2.forward busy none
3.Forw.no ans. none
call pick up group-none
Configure FXO Ports:
-Hit 3/1/1 as mentioend above
a.MGCP Member Configuration
Port type:loop start
b.Mgcp member information
- description:R3640A 3/1/0 FXO
- device pool:default
- calling search space:none
- location:none
c. Port information
- port direction:bothways
- Attendant DN:3000 &3001(on other fxo port)
Configured a route pattern
1.route plan>route pattern
a.Route Pattern Configuration
I.Pattern definition
-route pattern:9.@
-partition:none
-numbering plan:north america num. plan
-route filter:none
-gatway/route list: AALN/S3/SU0/0@R3640A
-route option: route this pattern
- provide outside dial tone:yes
II.Calling Party Tranformations
-use calling party's external phone number mask
(unchecked)
-calling party transform mask :blank
III.Called Party Transformations
-discards digits:predot
-called party transform mask: blank
-prefix digits(outgoing calls): blank
