cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3989
Views
0
Helpful
2
Replies

N7K-M224XP-23L :: Failed to enable 1000base-T SFP

danailpetrov
Beginner
Beginner

Hello guys,

I am experiencing very strange problem. I have a few 1000Base-T SFPs plugged into M2 card. However, for some reason I am getting this:

# show int ethernet 6/19 - 22 brief

Eth6/19       --      eth  routed down      Transceiver speed does no   10G(D) --

Eth6/20       3967    eth  trunk  down    Transceiver speed does no   10G(D) --

Eth6/21       3967    eth  trunk  down    Transceiver speed does no   10G(D) --

Eth6/22       3967    eth  trunk  down    Transceiver speed does no   10G(D) --

# show int ethernet 6/19 - 22 cap | egrep "(Ethernet|Model|Type|Speed|Duplex)"

Ethernet6/19

  Model:                 N7K-M224XP-23L

  Type (SFP capable):    1000base-T

  Speed:                 10000 <------------- that's odd?

  Duplex:                full

Ethernet6/20

  Model:                 N7K-M224XP-23L

  Type (SFP capable):    1000base-T

  Speed:                 10000

  Duplex:                full

Ethernet6/21

  Model:                 N7K-M224XP-23L

  Type (SFP capable):    1000base-T

  Speed:                 10000

  Duplex:                full

Ethernet6/22

  Model:                 N7K-M224XP-23L

  Type (SFP capable):    1000base-T

  Speed:                 10000

  Duplex:                full

esmdrsv9001(config-if-range)# speed 1000

ERROR: Ethernet6/19-22: Configuration does not match the port capability.

Here is some additional information that might help.

# show module

Mod  Ports  Module-Type                         Model              Status

---  -----  ----------------------------------- ------------------ ----------

1    0      Supervisor module-2                 N7K-SUP2           active *

2    0      Supervisor module-2                 N7K-SUP2           ha-standby

5    48     1/10 Gbps Ethernet Module           N7K-F248XP-25E     ok

6    24     10 Gbps Ethernet Module             N7K-M224XP-23L     ok

Mod  Sw              Hw

---  --------------  ------

1    6.1(2)          1.1

2    6.1(2)          1.1

5    6.1(2)          1.0

6    6.1(2)          1.2

Could that be a problem with an unsupported SFP for this module? I checked this one, but couldn't find any 1Gbps SFPs as supported..

Any thoughts are more than welcome!

Sincerely,

D.

1 Accepted Solution

Accepted Solutions

Steve Fuller
Engager
Engager

Hi Danail,

The N7KM224XP-XL only support 10 Gigabit Ethernet speeds and so unfortunately the 1000BASE-T transceivers you have will not work in this module.

Regards

View solution in original post

2 Replies 2

Steve Fuller
Engager
Engager

Hi Danail,

The N7KM224XP-XL only support 10 Gigabit Ethernet speeds and so unfortunately the 1000BASE-T transceivers you have will not work in this module.

Regards

So my fears got confirmed ...

ta Steve!

D.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: