Well, not much info from that

Geir Sand-Strand · ‎03-28-2014

Hi, I’ve got this problem with my N7K and 2 of the fabric module’s. The front LED of the N7K is yellow/orange instead of green (it’s supposed to be green I believe). Not sure what this relates to, hw issue, config issue or?

As you can see below, 2 of the fabric module are powered down. Restarting the fab’s og restarting the N7K does not power up the fab module’s.

VDC-ADMIN# sh module

Mod Ports Module-Type Model Status

--- ----- ----------------------------------- ------------------ ----------

4 12 10/40 Gbps Ethernet Module N7K-F312FQ-25 ok

5 0 Supervisor Module-2 N7K-SUP2E active *

6 0 Supervisor Module-2 N7K-SUP2E ha-standby

7 12 10/40 Gbps Ethernet Module N7K-F312FQ-25 ok

10 4 Network Analysis Module NAM-NX1 N7K-SM-NAM-K9 ok

Mod Sw Hw

--- -------------- ------

4 6.2(6a) 1.0

5 6.2(6a) 6.0

6 6.2(6a) 6.0

7 6.2(6a) 1.0

10 6.2(6a) 1.0

Mod Application Image Description Application Image Version Status

-------- ---------------------------- ------------------------- ------

10 Application linecard image 6.0(1) ok

Mod MAC-Address(es) Serial-Num

--- -------------------------------------- ----------

4 28-34-a2-ab-e1-dc to 28-34-a2-ab-e2-17 JAE181002NA

5 e4-c7-22-10-2f-4f to e4-c7-22-10-2f-61 JAF1748AFJR

6 e4-c7-22-0f-dd-13 to e4-c7-22-0f-dd-25 JAF1748AFKG

7 54-4a-00-ac-09-d8 to 54-4a-00-ac-0a-13 JAE181002PX

10 e4-c7-22-0f-95-e6 to e4-c7-22-0f-95-ef JAF1801AABH

Mod Online Diag Status

--- ------------------

4 Pass

5 Pass

6 Pass

7 Pass

10 Pass

Xbar Ports Module-Type Model Status

--- ----- ----------------------------------- ------------------ ----------

1 0 Fabric Module 2 N7K-C7010-FAB-2 ok

2 0 Fabric Module 2 N7K-C7010-FAB-2 ok

3 0 Fabric Module 2 N7K-C7010-FAB-2 ok

4 0 Fabric Module 2 N7K-C7010-FAB-2 powered-dn

5 0 Fabric Module 2 N7K-C7010-FAB-2 powered-dn

Xbar Power-Status Reason

--- ------------ ---------------------------

4 powered-dn Reset (powered-down) because module does not boot

5 powered-dn Reset (powered-down) because module does not boot

Xbar Sw Hw

--- -------------- ------

1 NA 1.5

2 NA 1.5

3 NA 1.5

Xbar MAC-Address(es) Serial-Num

--- -------------------------------------- ----------

1 NA JAF1749AFAB

2 NA JAF1749AFDF

3 NA JAF1748AEQR

4 NA JAF1746BEFB

5 NA JAF1749AMCA

* this terminal session

VDC-ADMIN#

richbarb · ‎03-29-2014

Hello,

This command might help you to know what happened.

#show environment power

Regards,

Richard

Geir Sand-Strand · ‎03-30-2014

Well, not much info from that command.

VDC-ADMIN# sh environment power
Power Supply:
Voltage: 50 Volts

Power Actual Total

Supply Model Output Capacity Status

(Watts ) (Watts )

------- ------------------- ----------- ----------- --------------

1 N7K-AC-6.0KW 800 W 6000 W Ok

2 N7K-AC-6.0KW 641 W 6000 W Ok

3 ------------ 0 W 0 W Absent

Actual Power

Module Model Draw Allocated Status

(Watts ) (Watts )

------- ------------------- ----------- ----------- --------------

4 N7K-F312FQ-25 289 W 340 W Powered-Up

5 N7K-SUP2E 128 W 265 W Powered-Up

6 N7K-SUP2E 128 W 265 W Powered-Up

7 N7K-F312FQ-25 281 W 340 W Powered-Up

10 N7K-SM-NAM-K9 333 W 750 W Powered-Up

Xb1 N7K-C7010-FAB-2 39 W 80 W Powered-Up

Xb2 N7K-C7010-FAB-2 39 W 80 W Powered-Up

Xb3 N7K-C7010-FAB-2 44 W 80 W Powered-Up

Xb4 N7K-C7010-FAB-2 N/A 80 W Powered-Dn

Xb5 N7K-C7010-FAB-2 N/A 80 W Powered-Dn

fan1 N7K-C7010-FAN-S 198 W 720 W Powered-Up

fan2 N7K-C7010-FAN-S 198 W 720 W Powered-Up

fan3 N7K-C7010-FAN-F 14 W 120 W Powered-Up

fan4 N7K-C7010-FAN-F 14 W 120 W Powered-Up

N/A - Per module power not available

Power Usage Summary:

--------------------

Power Supply redundancy mode (configured) PS-Redundant

Power Supply redundancy mode (operational) PS-Redundant

Total Power Capacity (based on configured mode) 6000 W

Total Power of all Inputs (cumulative) 12000 W

Total Power Output (actual draw) 1441 W

Total Power Allocated (budget) 4040 W

Total Power Available for additional modules 1960 W

VDC-ADMIN#

sean_evershed · ‎03-30-2014

Are you sure the switch hasn't been configured this way?

You can manually power down the fabics in order to minimise overall power by using the command poweroff xbar. See below:

http://www.cisco.com/c/en/us/td/docs/switches/datacenter/hw/nexus7000/installation/guide/n7k_hig_book/n7k_managing_sys_hw.html#wp1052265

Geir Sand-Strand · ‎03-31-2014

The N7K is brand new, and the Fab mod.2 in slot 4 and 5 has been like this from the first start-up. Below is output sh module fabric 4, and attached logfile from the command no poweroff xbar 4

VDC-ADMIN# sh module fabric 4

Xbar Ports Module-Type Model Status

--- ----- ----------------------------------- ------------------ ----------

4 0 Fabric Module 2 N7K-C7010-FAB-2 powered-dn

Xbar Power-Status Reason

--- ------------ ---------------------------
4 powered-dn Reset (powered-down) because module does not boot

Xbar Sw Hw

--- -------------- ------

Xbar MAC-Address(es) Serial-Num

--- -------------------------------------- ----------

4 NA JAF1746BEFB

Chassis Ejector Support: Enabled

Ejector Status:

Left ejector CLOSE, Right ejector CLOSE, Module HW does support ejector based shutdown, Ejector policy enabled.

VDC-ADMIN#

Se attachment for output of no poweroff xbar 4.

Geir Sand-Strand · ‎04-30-2014

Problem solved. Had to replace the N7K chassis.

Problem with Fabric Module 2 in Nexus 7010