08-03-2015 10:33 PM - edited 03-01-2019 07:59 AM
hi folks,
Recently I Have configured VSS in cat 6509 switch in my data center after completion of all configuration both switches standby supervisors getting red color lights.
I observed that standby supervisor goes to rommon mode.
I have attached output document so please verify and give me some tips to resolve this problem.
rommon 2 >
rommon 2 > confreg 0x2102
You must reset or power cycle for new config to take effect
rommon 3 > reset
Resetting .......
System Bootstrap, Version 12.2(50r)SYS3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2012 by cisco Systems, Inc.
PYRAMID platform with 2097152 Kbytes of main memory
Autoboot executing command: "boot bootdisk:s2t54-advipservicesk9-mz.SPA.150-1.SY7.bin"
bootdisk:%s72044-atafslib-m: Digitally Signed Release Software with key version A
Initializing ATA monitor library...
bootdisk:s2t54-advipservicesk9-mz.SPA.150-1.SY7.bin: Digitally Signed Release Software with key version A
Self extracting the image... [OK]
Self decompressing the image :
##########################################################################################################################
##########################################################################################################################
##########################################################################################################################
######################################################################################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s2t54 Software (s2t54-ADVIPSERVICESK9-M), Version 15.0(1)SY7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 24-Jul-14 11:04 by prod_rel_team
Image text-base: 0x04000144, data-base: 0x0C000000
System detected Virtual Switch configuration...
Interface TenGigabitEthernet 1/5/4 is member of PortChannel 200
Interface TenGigabitEthernet 1/5/5 is member of PortChannel 200
Interface TenGigabitEthernet 1/6/4 is member of PortChannel 200
Interface TenGigabitEthernet 1/6/5 is member of PortChannel 200
*Aug 4 06:27:33.807: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
Firmware compiled 25-Jun-14 09:42 by integ Build [25856]
*Aug 4 06:27:33.807: %PFREDUN-6-STANDBY: Initializing as STANDBY processor for this switch
*Aug 4 06:27:40.675: %SYS-SW1_STBY-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Aug 4 06:27:34.107: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Aug 4 06:27:40.675: %PFREDUN-SW1_STBY-6-STANDBY: Initializing as STANDBY processor for this switch
*Aug 4 06:27:41.047: %SYS-SW1_STBY-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Aug 4 06:27:41.055: SW1_STBY: vs_ha_send_hb_start_msg:Sending start req with
MyEobcAddr : 262
Frequency : 1000
Timeout : 179000
Version : 1
*Aug 4 06:27:41.055: SW1_STBY: vs_ha_ps_bootup_icc_msg_hdlr:** PSEUDO STDBY NOT SUPPORTED DROPPING TO ROMMON **
*Aug 4 06:27:41.055: %PFREDUN-SW1_STBY-4-SUP_FORCE_TO_ROMMON: Supervisor forced to rommon with reason: Cannot continue...
disabling autoboot and resetting
Resetting .......
System Bootstrap, Version 12.2(50r)SYS3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2012 by cisco Systems, Inc.
PYRAMID platform with 2097152 Kbytes of main memory
rommon 1 >
65K01#sh switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = none
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :
-----------------------------------------------
Current Software state = ACTIVE
Uptime in current state = 3 days, 17 hours, 13 minutes
Image Version = Cisco IOS Software, s2t54 Software (s2t54-ADVIP SERVICESK9-M), Version 15.0(1)SY7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 24-Jul-14 11:04 by prod_rel_team
BOOT = bootdisk:s2t54-advipservicesk9-mz.SPA.150-1.SY7 .bin,12;bootdisk:s2t54-advipservicesk9-mz.SPA.150-1.SY3.bin,12;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Fabric State = ACTIVE
Control Plane State = ACTIVE
Switch 2 Slot 5 Processor Information :
-----------------------------------------------
Current Software state = STANDBY HOT (switchover target)
Uptime in current state = 4 minutes
Image Version = Cisco IOS Software, s2t54 Software (s2t54-ADVIP SERVICESK9-M), Version 15.0(1)SY7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 24-Jul-14 11:04 by prod_rel_team
BOOT = bootdisk:s2t54-advipservicesk9-mz.SPA.150-1.SY7 .bin,12;bootdisk:s2t54-advipservicesk9-mz.SPA.150-1.SY3.bin,12;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Fabric State = ACTIVE
Control Plane State = STANDBY
65K01#sh switch virtual link
VSL Status : UP
VSL Uptime : 7 minutes
VSL SCP Ping : Pass
VSL ICC Ping : Pass
VSL Control Link : Te1/5/5
VSL Encryption : Configured Mode - Off, Operational Mode - Off
HBDCITZWSL65K01#sh red
HBDCITZWSL65K01#sh redundancy s
HBDCITZWSL65K01#sh redundancy st
HBDCITZWSL65K01#sh redundancy states
my state = 13 -ACTIVE
peer state = 8 -STANDBY HOT
Mode = Duplex
Unit = Primary
Unit ID = 21
Redundancy Mode (Operational) = sso
Redundancy Mode (Configured) = sso
Redundancy State = sso
Maintenance Mode = Disabled
Manual Swact = enabled
Communications = Up
client count = 137
client_notification_TMR = 30000 milliseconds
keep_alive TMR = 9000 milliseconds
keep_alive count = 0
keep_alive threshold = 18
RF debug mask = 0x0
regards
aslam
08-04-2015 12:56 AM
Hi,
apparently your configuration VSS is quad supervisors VSS (VS4O)...
VS4O is available for Sup2T beginning with Cisco IOS Software Release 15.1(1)SY1.
You IOS Release is 15.0(1)SY7...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide