05-14-2002 01:38 AM - edited 03-01-2019 09:43 PM
Hi All
This is really sad and basic but I can't crack it!!
Have a dial prob that consists of:
Win2K laptop with Xircom combo PC card dialing into a 1720 with WIC-1T in async mode and USR Sportster attached to it with CAB-232MT. Show Line gives TTY 1. Modem TR and CS lights are up OK
When I dial in with the laptop, the terminal window pop's up, nothing happens until after a few seconds, then the User Access Verification prompt from the router appears at the same time as a Network and Dial-up connection error saying "The script has halted".
As I'm getting the prompt from the router, something is working OK but what is halting the login process? Can anyone shed some light on a basic prob that I really should be able to overcome? (How embarassing!)
NAS config:
version 12.2
no parser cache
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
no logging buffered
logging rate-limit console 10 except errors
enable secret 5 $1$Wr8k$8rHh.QTYXuU6Db.5zDSrb1
enable password dog8dog
!
memory-size iomem 15
ip subnet-zero
!
no ip dhcp-client network-discovery
!
!
!
interface BRI0
no ip address
shutdown
!
interface FastEthernet0
ip address 10.1.1.1 255.255.255.0
speed auto
!
interface Serial0
physical-layer async
ip address 10.1.2.1 255.255.255.0
encapsulation ppp
!
ip classless
no ip http server
!
!
line con 0
exec-timeout 0 0
password front door
login
line 1
password dial-users
login
modem InOut
modem autoconfigure type usr_sportster
transport input all
stopbits 1
speed 115200
flowcontrol hardware
line aux 0
password admin-dial
login
line vty 0 4
password echo9
login
!
no scheduler allocate
end
Router#
Cheers
Ali
05-14-2002 10:31 AM
Put the following under serial 0 :
async mode dedicate
ppp authen chap
peer default ip address pool something
And now in global , define :
username Ali password cisco
ip local pool something 10.1.3.1
And dial in with username/password of Ali/cisco and see what you get.
~Zulfi
05-15-2002 01:26 AM
Hi Zulfi,
I've tried your recommendations but with the same results...
Basically, I'm trying to emulate the lab for the MCNS course. The course material has the NAS configs, but as I have a slightly different platform I'm trying to get this going.
It goes a LITTLE further though as the S0 changes state to UP/DOWN. However it quickly goes to RESET and drops out.
Any other suggestions please
Ali
05-15-2002 02:43 AM
I now have UP/UP ont S0 but still no readable Access Verification
05-14-2002 02:01 PM
What exactly you want to do after dialin? You want to do PPP or Exec?
In case of PPP you need to configure the serial interface with following
int s0
physical-layer async
ip address 10.1.2.1 255.255.255.0
encapsulation ppp
dialer-group 1
peer default ip address pool dialin
dialer in-band
dialer idle-timeout 600
async mode interactive
ppp authentication chap pap callin
!
ip local pool dialin 10.1.2.2 10.1.2.5
dialer-list 1 proto ip permit
!
Just add the command "autoselect ppp" under the line 1..
Above config will serve both the purpose for you.
Any reason for "bringing terminal window after dialing" at the client side
05-15-2002 01:39 AM
Hi Tejal,
OK I've tried your recommendations also. Same results EXCEPT, when the After Dial terminal window opens I see a scipt running only it's all gobbledy-gook then the error "Script has halted" appears again.
BTW, yes I'm trying to get Exec. The next stage is to achieve PPP.
Ali
05-22-2002 02:08 AM
IF YOU'RE INTERESTED...
The problem was the Win2k dial client. Disabling the terminal window, putting login local under the line for the S0 port and adding user/pass worked OK.
So it's a Win2k prob. Thanks for the suggestions.
Ali
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide