I have been presented with the following output from the command'show ip topology summary'I am very interested in the Quiescent interfaces and what this really means. Interfaces that are quiet or doing nothing?I can not find much information on this ...
Forum Posts
Hi there, I would like to ask you about something really strange on my router c4431. IOS is 3.13.04.S, MD, not deferred. I have multiple PAT configured as example, with pool of two public address ip nat pool NAT_10 xxx.32 xxx.33 netmask 255.255.255....
Good Day All, We recently upgraded our wireless infrastructure with new Cisco WAPs. Of course, now all our original WAPs on the Campus Maps are showing dissociated. We did a one for one replacement and didn’t change the locations on the new WAPs. H...
Resolved! CGNAT
Hi All , What is the CGNAT ? . what is the main difference between NAT and CGNAT .
Hi! Could you tell me the difference between these terms? End of LifeEnd of SaleEnd of SupportLast day of Support
Hi, I have a netflow .csv and I cant' find information on how to read the sampling column. My the rows show sampling =1, and I thought it means there was no sampling because it is 1:1. But someone told me it is still sampled. Does this mean that hi...
Resolved! Two Uplinks / Ports 25 & Port 26 (ports on each side on a different VLAN/uplink) - SG200-26P
Hello, I currently have a Cisco SG200-26P that has 2 uplink ports coming into it (Ports 25 & 26). The goal is to create VLANs in a way that when you plug a cable on the left side of the switch, it connects to the port 25 uplink, and acquires an IP f...
Hi, I have a topology like in the figure below. I want to limit the traffic of the PCs up to maximum 1 mpbs seperately. I mean 10.10.41.10 , 10.10.41.35 and 10.10.41.57 should use just up to 1 mbps seperately when they try to reach 10.10.25.0/24 ne...
What is the difference between them? If I connect network infrastructure directly to a power feed A, and behind that is a diesel generator for backup power. Does a diesel generator work instantaneously, so there is in effect "no break"? In such a...
Looking for a way to send ACL permit or deny hits to syslog only. We currently have a few routers that we need to monitor traffic out to the internet. We need to see what is permitted and what is denied. Currently, it is set up with a log command on ...
Resolved! CCNP Routing and Switch Renewal
I had a quick question regarding my CCNP Routing and Switching renewal. On Cisco it states: Pass any current 642-XXX Professional-level or any 300-XXX Professional-level exam I was already planning on going for CCNP Security, so does that mean tha...
I am trying to set up a Cisco 2620XM router to connect to the internet. I have never had to deal with routers before and am at a loss. I am doing this as a test project before getting budget to do production. I currently have fa0/0 and serial 0/0 a...
Hi All, I have a requirement where I want to allow ping access only to management interface IP. Since I need to do this config on many routers I don't want to go and configure IP address in each and every router access-list, is there way that I ca...
Hello, I have deployed 2 Cisco 4500X and connected the many devices arround (Router, switches, firewalls, BlueCoat proxy SG as well,etc....) using the GLC-T and SFP. For the BlueCoat appliance I used a GLC-T ( the PID and VIC are not specifyed); it...
We have customer which has 40Gbps (or close to 60Gbps in future) requirement for data transfer, I am looking for good and cheaper solution to handle 40Gbps. I am thinking to put 5548P nexus switch at core and N3K at access layer so my network design ...
