Cisco 2611 with 1enet

tung · ‎09-25-2004

Hello, what we trying to do is have an extra Ethernet interface for our DMZ. I added an 1enet to our cisco 2611 router but the router didn't seem to see it. can someone help me what is going on? Thanks

Georg Pauwen · ‎09-25-2004

Hello,

the WIC-1ENET is not compatible with the 2611, hence it will not work with your router. Check this document:

WAN Interface Card (WIC) / Platform Hardware Compatibility Matrix for 1600, 1700, 2600, 3600 and 3700 Series Routers

http://www.cisco.com/en/US/partner/products/hw/modules/ps3129/products_tech_note09186a00800ae37f.shtml

HTH,

Georg

www.solutionfinders.nl

Tsasbrink · ‎09-26-2004

all true, but a nm-1e or nm-4e will work on a 2611.

jlingerf · ‎09-26-2004

You likely need a version of code that supports the NM-1E. Can you paste in a show diag and show ver for the router while the card is in and not working?

tung · ‎09-26-2004

here is the show version.

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE SOFTWARE (fc

1)

Compiled Tue 17-Aug-99 13:18 by cmong

Image text-base: 0x80008088, data-base: 0x80CB67B0

ROM: System Bootstrap, Version 11.3(2)XA3, PLATFORM SPECIFIC RELEASE SOFTWARE (f

c1)

Cisco2611 uptime is 27 minutes

System returned to ROM by reload

System image file is "flash:c2600-do3s-mz.120-5.T1.bin"

cisco 2611 (MPC860) processor (revision 0x202) with 39936K/9216K bytes of memory

.

Processor board ID JAB023801WX (3019133771)

M860 processor: part number 0, mask 32

Bridging software.

X.25 software, Version 3.0.0.

2 Ethernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

jlingerf · ‎09-26-2004

Can you put a show diag in here as well captured when the wic is installed in the router? Thanks..Jamie

tung · ‎09-26-2004

C2611 2E Mainboard port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 2.2 Board revision A0

Serial number 3019133771 Part number 73-2840-08

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 92 02 02 B3 F4 53 4B 49 0B 18 08 00 00 00 00

0x30: 50 00 00 06 00 00 00 00 00 00 00 00 00 00 00 00

WIC Slot 0:

Unknown WAN daughter card

Hardware revision 64.0 Board revision G0

Serial number 960561920 Part number 800-3295510-165

Test history 0x3 RMA number 66-65-48

Connector type PCI

EEPROM format version 4

EEPROM contents (hex):

0x20: 04 FF 40 00 39 41 03 00 82 49 16 A5 03 42 41 30

0x30: 80 00 00 00 00 02 02 C1 8B 56 4D 53 30 36 31 38

WIC Slot 1:

Serial 1T WAN daughter card

Hardware revision 1.1 Board revision A0

Serial number 4585802 Part number 73-1775-02

Test history 0x0 RMA number 00-00-00

Connector type Wan Module

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 02 01 01 00 45 F9 4A 49 06 EF 02 00 00 00 00

0x30: 50 00 00 00 97 01 14 01 FF FF FF FF FF FF FF FF

jlingerf · ‎09-26-2004

This card is a wic-1enet card. It is only supported in a 1700 series router. The only options for adding a eth port to your router would be to add a NM-1E or NM-4E card. FE is not supported. I would recommend using a 2620 series or XM series that has FE ports that support dot1q tagging and plug it into a 2950 or 2940 series switch that supports dot1q as well. The reason is that you will be able to create dot1q "subinterfaces". This will allow you to have as many interfaces on the router as you have switch ports..Thanks and good luck....

tung · ‎09-27-2004

Thanks for the tips.

Tsasbrink · ‎09-29-2004

A 2611 b.t.w. can already do 802.1q tagging with 12.2 or higher ip plus software.