Looking at the Chassis-Ser-EEPROM:Fan: F is this error that can cau

ccoletti · ‎04-05-2005

Hello Everyone,

I came across and message while going through my morning check list from my catalyst switches, The show environment all command, noticed an issue from a Cisco catalyst switch running Hardware Version: 2.0 Model: WS-C6509. I also included a show version, Looking at the Chassis-Ser-EEPROM: Fan: F is this error that can cause the switch to fail and can I live with it or should I open a case with Cisco and have a part replaced.

Thank you

Rq,

Charlene

(enable) sh environment all

Environmental Status (. = Pass, F = Fail, U = Unknown, N = Not Present)

PS1: . PS2: . PS1 Fan: . PS2 Fan: .

Chassis-Ser-EEPROM: . Fan: F

Clock(A/B): A Clock A: . Clock B: .

VTT1: . VTT2: . VTT3: .

Intake Exhaust Device 1 Device 2

Slot Temperature Temperature Temperature Temperature

--------------- --------------- --------------- --------------- ---------------

1 21C(50C,65C) 29C(60C,75C) 25C 28C

2 20C(50C,65C) 27C(60C,75C) 24C 24C

4 18C(50C,65C) 27C(60C,75C) 31C 25C

6 17C(50C,65C) 23C(60C,75C) 23C 29C

7 20C(50C,65C) 25C(60C,75C) 20C 22C

1 (Switch-Eng) 25C(50C,65C) 27C(60C,75C) N/A N/A

2 (Switch-Eng) 24C(50C,65C) 28C(60C,75C) N/A N/A

1 (MSFC) 21C(60C,70C) 26C(60C,75C) N/A N/A

2 (MSFC) 19C(60C,70C) 27C(60C,75C) N/A N/A

Chassis Modules

---------------------

VTT1: 20C(85C,100C)

VTT2: 23C(85C,100C)

VTT3: 22C(85C,100C)

PS1 Capacity: 1153.32 Watts (27.46 Amps @42V)

PS2 Capacity: 1153.32 Watts (27.46 Amps @42V)

PS Configuration : PS1 and PS2 in Redundant Configuration.

Total Power Available: 1153.32 Watts (27.46 Amps @42V)

Total Power Available for Line Card Usage: 1153.32 Watts (27.46 Amps @42V)

Total Power Drawn From the System: 574.56 Watts (13.68 Amps @42V)

Remaining Power in the System: 578.76 Watts (13.78 Amps @42V)

Default Inline Power allocation per port: 7.00 Watts (0.16 Amps @42V)

Slot power Requirement/Usage :

Slot Card Type PowerRequested PowerAllocated CardStatus

Watts A @42V Watts A @42V

---- ------------------- ------- ------ ------- ------ ----------

1 WS-X6K-SUP1A-2GE 138.60 3.30 138.60 3.30 standby

2 WS-X6K-SUP1A-2GE 138.60 3.30 138.60 3.30 ok

4 WS-X6408-GBIC 84.00 2.00 84.00 2.00 ok

6 WS-X6248-RJ-45 112.98 2.69 112.98 2.69 ok

7 WS-X6348-RJ-45 100.38 2.39 100.38 2.39 ok

SW10 (enable) sh ver

WS-C6509 Software, Version NmpSW: 6.3(5)

NMP S/W compiled on Feb 7 2002, 19:52:15

System Bootstrap Version: 5.3(1)

Hardware Version: 2.0 Model: WS-C6509

PS1 Module: WS-CAC-1300W Serial #:

PS2 Module: WS-CAC-1300W Serial #:

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP1A-2GE Hw : 7.0

2 2 WS-X6K-SUP1A-2GE Hw : 7.0

4 8 WS-X6408-GBIC Hw : 2.3

6 48 WS-X6248-RJ-45 Hw : 1.1

7 48 WS-X6348-RJ-45 Hw : 1.4

15 1 WS-F6K-MSFC2 Hw : 1.1

16 1 WS-F6K-MSFC2 Hw : 1.1

b.orth · ‎04-06-2005

Is there any errors in sh logg buff 1023?

Assuming you are running CAT OS:

This may give you more information.

Yes, I would open a TAC case.

But your temperatures all look good so it is probably not critical.

HTH

ccoletti · ‎04-07-2005

Very Cool, Thank you so very much for the update.

Prashanth Krishnappa · ‎04-06-2005

Do a "sh system" and check for the fan status. if it says faulty, have the fan tray replaced.

ccoletti · ‎04-07-2005

Hi,

Correct, thank you so very much for the update.