12-08-2003 05:45 PM - edited 03-02-2019 12:12 PM
In my router .why have this commad??it is copy run strat.
Router#copy run strat
Destination filename [strat]?
Erase flash: before copying? [confirm]
Imprudence to enter .my flash is erased.. Now ,I want to pour the IOS again. But the system clew that the memory is not enough to download image¡I don¡¯t kown why..
rommon 1 > xmodem ?
Do not start the sending program yet...
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
ERR: Not enough memory to download image
router#show flash
System flash directory:
No files in System flash
[0 bytes used, 16777216 available, 16777216 total16384K bytes of processor board System flash (Read/Write)
router#show version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(15)T9, RELEASE SOFTWARE (fc2)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Sat 01-Nov-03 04:42 by ccai
Image text-base: 0x80008098, data-base: 0x80C294DC
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
router uptime is 7 hours, 46 minutes
System returned to ROM by power-on
Running default software
cisco 2621XM (MPC860P) processor (revision 0x100) with 27648K/5120K bytes of mem
ory.
Processor board ID JMX0636112S (3333293542)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x3922
But I pour the ios,the system is running in gear¡¡.why ?????
12-08-2003 10:56 PM
I don't think there's such a command. When yu issue "copy run strat" you're trying to copy running-confing to a file named "strat". May it be "copy run start" (to copy running-config to startup-config).
12-09-2003 06:02 PM
I kown that it have the command "copy run start"in router,this is in gear.But the command "copy run strat" also is in gear,so i don't understand.please tell me why..thank you !
Now,i can't pour the new's IOS,when i pour the IOS,the system clew that the storage'space is not enough,But i inport the command "show flash" in router,show out :
ks_pouchen#show flash
System flash directory:
No files in System flash
[0 bytes used, 16777216 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)
Why this.....i don't understand..
12-09-2003 11:03 PM
Can you send output starting with command "copy tftp:..... flash:....."
The IOS image you're trying to copy may be larger than the flash can handle.
12-11-2003 01:09 AM
I understand your means.But the flash's range is 16M in my router, the new ios's range is 6.4M.
12-11-2003 05:22 AM
Have you tried to squeeze flash ? (squeeze flash:).
12-12-2003 01:01 AM
No,no ...i don't want to squeeze flash ,i only want to pour the new's flash,but working ,the system have some question.my flash's space is enough,but the system clew the space is not enough..
router#show flash
System flash directory:
No files in System flash
[0 bytes used, 16777216 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)
why? i don't know the means.
12-12-2003 02:58 AM
Hi,
try complete xmodem command on rommon. Because you wrote "xmodem ?", router gets ? as filename. for help on xmodem command try "xmodem -?" you can look at link below..
xmodem -c
12-16-2003 05:50 PM
Thank's your answer my question..Now i also find a new question,it is a new's command that "copy run (*.*),it means that the * may be any letter. as for as you input copy run any letter .you can receve the same result.please see ..
ks_pouchen#copy run a
Destination filename [a]?
Erase flash: before copying? [confirm]
please answer me ..thank you ....
wsline.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide