Other Security Subjects

One of our clients is using a PIX 525 whith SW 5.32. Now they have requested to enable the MSN Messenger service for their end users. Basically, it was not a problem, we have opened the port 1863 and could establish a connection to an outside user. T...

I'm running PIX version 4.2.5.. Is there any way for me to specify multiple gateways? Having some redundancy in this area would be nice.If this is not possible, what is standard practice to ensure a router is not a single point of failure? Thanks in ...

I am try to setup limited access on all lines on a router with certain privileges for certain users in the local user database but it doesn’t seem to be working. If I login with "tcsuser" via a VTY line everything works fine, the user is only able t...

I have fully configured both the CSPM 2.3i and (2) CSIDS 4230s (2.5). The sensors are capturing traffic, all of the services are running, and communication is established with CSPM. I've configured my signatures but am getting no alerts when I should...

my route has following configuration:access-list 1 permit 0.0.0.0access-list 1 permit 131.108.0.0 0.0.15.255access-list 1 deny 1.1.0.0 255.255.255.255I can't understand what's mean of these.my question is :1.access-list 1 permit 0.0.0.0 permit what r...

i know that cisco does not currently support a mac client for this device but has anyone successfully used another ipsec client for the macs? ie. pgp or other?

Is there a simple solution to block thses sites by ports or do we have to block them strictly by ip address.Thanks,Bob

Hi,I have some clýents who stay at outside part of PIX, and they must connect to all sites at inside part of the PIX. I can't write static NAT ( there are a lot of sýtes ) to all sýtes. Is there any way makýng NAT for outside IPs. I wrote it. But it ...

We have standardized on the Cisco 3030 VPN concentrator within our organization and we need one of our vendors to establish an IPSec connection from their network. However, this vendor has Nortel Contivity clients installed on their workstations. Ha...

Hi, I read this articel http://www.cisco.com/warp/public/105/56.html, and was wondering about one thing. Why is it said in the articel that if you change MTU on one client you should change it on all clients on the same network ?

I have two 2620 routers each with an AIM-VPN/BP hardware encryption module. They both have a T1 to an ISP, and we have a VPN tunnel set up between them. I can send data through without any problem and I get the desired T1 speed that I want. Howeve...

We use netranger 2.2.1.8 and CSPM 2.5, I couldn't change alert level "route down"(connection error of postoffice daemon) from CSPM. We confirmed that default level is "5". Please tell me how to change it down.

Hello.A customer has two ISPs, each in a different city. The ISP in the main office goes down occasionally and they want the other ISP to serve as a backup for the whole firm when this happens.Their environment: Connection to ISP in each city is via ...

Some one post this question on the board I am reposting it here so we can get some thoughts from very experinced guys like you,here we go:"I have a question for you guys. I have been giving some thought about the configuration register and password r...

Will this static config work based on the defined global & nat command?global (outside) 1 169.139.1.20-169.139.1.20 netmask 255.255.0.0global (ssn) 1 169.139.254.101-169.139.254.101 netmask 255.255.0.0nat (inside) 1 10.0.0.0 255.0.0.0 16384 11468nat...