What is the best way to configure a guest network? The guest network would have access to the Internet only. The guest network will would not have access to servers. We have a an ASA firewall, Cisco router and L3 switch. Thanks.
What is the best way to configure a guest network? The guest network would have access to the Internet only. The guest network will would not have access to servers. We have a an ASA firewall, Cisco router and L3 switch. Thanks.
Hello,I have the need to reboot my ASA5520. We have a Active/Standby pair and I want to make sure that they come up playing nicely and not in a tug of war.Any advice on the proper way to reload these machines and optimize uptime??Thanks,Pedro
I am running 6.0.3 MARS, Data Package Version: 32, Signature Version: 396. We have recently stood up a Enterasys Dragon 7.2.3. I followed the instructions for adding the device type for a Dragon 6.x device and with some differences on the Enterasys ...
Hi,I am attempting to run an upgrade to a pair of FWSMs in active/standby from their 3.x version to a new major release of 4.0.7, which are in multiple context mode.When following the upgrade release notes and the managing software section of the FWC...
Dear all,I want to create multiple usernames on same router with different privilages, sothat, some of them can only monitor without editing router configuration and other usernames can edit configuration.And if i creat username, so, i can cancel VTY...
Hi All, I am trying to upgarde MARS by CLI: $pnupgrade ftp://10.0.103.140/upgrade/packages/csmars-5.3.3.2774.pkg username passwordit says "upgarde failed, invalid URL". I am pretty sure FTP and home directory are right. any idea would be very appreci...
Hi, I am using the MARS local controller with 6.0.4.3229 software. I was integrated MARS with CSM 3.2 and it was working fine. Now I decommission the present CSM server and install CSM 3.3 on new server. I remove the previous CSM configuration from M...
Hi,I have a CSS with many interfaces, all of them bridging.I need to include one routed interface. however, front end vlan is defined bridging, the new bac kend interface is to be routed with front end.mix og bridge mod and route mode, will it workmi...
Hi,Can the CSS, on bridge mode (Client VLAN10, Server VLAN10) just allow traffic through without load balancing.(I did this in ACE by defining access rules. I'm not sure about CSS.)Please point to a document where I can read about this too.Kind regar...
trying to upgrede mars 6.0.1 to 6.0.4 but it's faailing,here is the command I put when i ssh to the appliance with the Ip address (pnupgrade cdrom://package/csmars-6.0.2.3102.zip) so is there anything wrong there.
Hi,I am new to CSA and have been trying to figure out how to block the Windows cmd.exe process outright? Is anyoneableto assist or point me in the right directionthanks?
Interesting blog in the news this morning...http://networklore.com/rest-in-peace-cisco-security-agent/
hi,Newbie question here. how can i add a vlan to a fwsm module. What are the steps i should do? And also, can i directly assign the vlan i add to fwsm directly to a switchport (i.e. access switch)thanks.
I have console Kaspersky kit. How can I send log from kaspersky kit to Cisco MARS?Does Cisco Mars support antivirus Kaspersky?
Hi, Good day to all NetPros. I would like to ask something, and answers are greatly appreciated. Our company is running Pix515E software version 6.3(3). Our mother company did a network security audit, and found out that the appliance is runn...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 05:42 AM | ||
07-05-2024 02:02 AM | ||
06-27-2024 07:55 AM | ||
06-25-2024 12:23 PM | ||
06-06-2024 05:38 AM |