04-14-2010 03:58 AM - edited 03-01-2019 02:18 PM
I have installed the 7600-SIP-200 and SPA-4XT-SERIAL modules in the 6513 switch. Both modules have been detected. But, I received following error message:
“SLOT 1: 00:00:04: %SPA_OIR-3-UNSUPPORTED: The SPA-4XT-SERIAL in Subslot 0 is not supported by the SIP-200 module”
I had upgraded the IOS and had also changed the slot but still the same issue.
When I checked the Cisco documentation for 6500 switch, it says that it supports 7600-SIP-200 and SPA-4XT-SERIAL modules. "show module" of the router is as follows:
MOFWAN-6513#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE1322APKW
2 0 2-subslot Services SPA Carrier-400 7600-SSC-400 JAE13198KBI
3 6 Firewall Module WS-SVC-FWM-1 SAD1320016W
5 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1315N14R
7 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL1303GP73
8 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1327TC69
10 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1315MXX0
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0025.84e0.b5c0 to 0025.84e0.b5ff 2.303 12.2(33)SXH6 12.2(33)SXH6 Ok
2 0023.04e2.9eb8 to 0023.04e2.9ef7 2.0 12.2(33)SXH6 12.2(33)SXH6 Ok
3 0024.9773.e760 to 0024.9773.e767 4.5 7.2(1) 4.0(8) Ok
5 0025.4551.84c8 to 0025.4551.84f7 11.3 7.2(1) 8.7(0.22)BUB Ok
7 001a.a22d.6c2c to 001a.a22d.6c2f 5.7 8.5(2) 12.2(33)SXH6 Ok
8 0024.1499.535c to 0024.1499.535f 5.9 8.5(3) 12.2(33)SXH6 Ok
10 0024.c481.5ac0 to 0024.c481.5ad7 3.3 12.2(18r)S1 12.2(33)SXH6 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1/0 SPA-4XT-SERIAL JAE14080NGQ 2.0 AdmnDown
1/1 SPA-4XT-SERIAL JAE14080NH2 2.0 OutSrvc
2/0 SPA-IPSEC-2G JAE1332FXKP 2.0 OutSrvc
7 Policy Feature Card 3 WS-F6K-PFC3B SAL1303GMBR 2.4 Ok
7 MSFC3 Daughterboard WS-SUP720 SAL1303GKV0 3.2 Ok
8 Policy Feature Card 3 WS-F6K-PFC3B SAL1327TC0G 2.5 Ok
8 MSFC3 Daughterboard WS-SUP720 SAL1327T8E3 4.0 Ok
10 Distributed Forwarding Card WS-F6700-DFC3C SAL1322R0K4 1.2 Ok
Mod Online Diag Status
---- -------------------
1 Pass
1/0 Not Applicable
1/1 Not Applicable
2 Pass
2/0 Not Applicable
3 Pass
5 Pass
7 Pass
8 Pass
10 Pass
Please let me know what could be the possible issue?
04-26-2010 04:56 AM
Answered in WAN forum
Jerry confirmed this specific SPA is not accepted on C6500 chassis
Best Regards
Giuseppe
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide