Routers - Small Business

Hi gues,I configure ipsec tunnel between RV042 and WRV210. Both routers report connected but no traffic passed.RV042 - firmware 1.3.12.19-tmConnected 3DES/MD5/2 192.168.250.0/255.255.255.0 192.168.10.0/255.255.255.0 remote gateway 10.0.0.2WRV210 - fi...

Hi all,Is it true that the QuickVPN client only works when you have only 1 NIC connected to a network? I didn´t manage to get a connection to my office when I had both the wired and wireless connected at the same time. When I disconnected the wireles...

I am trying to connect an RV 120W using EZVPN to a Cisco ASA 5510.  I had Cisco TAC check the configuration on the ASA and it is correct, but they cannot help me with the 120W.  Is there a trick to configuring the vpn client on the 120W?  It can't ge...

This might be an easy question but I just cannot figure it out.- Externally we have a single IP address going to WAN1.- There are two replicating domain controllers that we need to remotely gain access to using LDAP (Port 389,636).How can we access b...

bought this router a few days back and trying to set up wireless part, but with no success at all. ive tryd almost anything and everything including updating firmware, changing settings... you name it.theres simply no way to configure this router to ...

I worked with Qwest yesterday to setup my router in the Qwest's DMZ mode so that I don't have to do port forwarding and such in 2 separate places and to generally simplify the overall configuration. The problem is that it doesn't seem to route proper...

We are using several SGE2000P switches and SPA502G IP-Phones.Config setting:Vlan 10     PC-DataVlan 20     VoiceThe Phones are width a trunk connected to the switch and the PC's are connected to the Phones.Vlan 10 untagged, Vlan 20 tagged.The Voice V...

I am using a Cisco RVS 4000 to test a new 10M/10M internet connection.  I'm having a small problem performing the ISP's speed test (speedtest.cavtel.net).  The download test consistently gives me 10Mbit/s, full speed for the connection, however the ...

Hi,I've been able to configure the VPN on a RSV4000 device. I have 2 Windows 7 clients that connects in that VPN.Everything works well except when both users tries to connect at the same time, they both kick each other out the VPN.They are behind the...

Hi there everyone,  Been working on this for 2 night already and still getting nowhere. Here is the configure.  Site A=======Local IP Address  ===> RV042 ==> ADSL Modem 192.168.50.x  ==>   192.68.50.1 ==> WAN IP (A.A.A.)   using DYNDNS.com (Dynamic I...

Hello,Is there any way to configure RV042 as DHCP relay agent? I'm using two of these routers with G2G configuration. In one location I have W2k3 DHCP server and in another location I want computers to use this server.Location 1: 10.0.0.0/24 - W2K3 S...

I have tried to use QuickVPN with our RV016 with little success.  It works only if I turn the RV016 Firewall off, make the connection, then turn it (the RV016 firewall) back on.  I requested info/assistance several months ago and got nowhere with tha...

I'm trying to evaluate the SRP527W as a dsl cpe device and I'm having trouble getting PPP to authenticate.  This may be compounded by the fact that I have a colleague configuring the 527 on his dsl connection and I'm working on this remote.  I will t...

I go to the Cisco Home page, login, and go to the Site Map. If I click on the link for the Software Center, I am redirected to http://www.cisco.com/public/sw-center/index.shtml. This link always gives the result "The connection to the server was rese...

Where is the firmware downloads for WRV54G?  I am looking for 2.39.2.e