I have a 2651 with a 4 port serial card. I cannot get any commands to work which might set the clock source. Is there another place in the IOS where I can set this?
FEIDATAR#show hard
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(20), RELEASE SOFTWARE (fc2)
cisco 2651 (MPC860P) processor (revision 0x200) with 28672K/4096K bytes of memory.
Processor board ID JAB05200C4C (4276647583)
M860 processor: part number 5, mask 1
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
4 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
------------------------------------------------------------------------------------------------------------------------------------
FEIDATAR(config-if)#clock ?
rate Configure serial interface clock speed
------------------------------------------------------------------------------------------------------------------------------------
Interface Serial0/1
Hardware is PowerQUICC MPC860
DTE V.35 TX and RX clocks detected.
idb at 0x815B81D8, driver data structure at 0x815BFFAC
SCC Registers:
General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8
Events [SCCE]=0x0300, Mask [SCCM]=0x001F, Status [SCCS]=0x03
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00367F80, Pending [CIPR]=0x00008C04
Mask [CIMR]=0x48204002, In-srv [CISR]=0x00000000
Command register [CR]=0x6C0
Port A [PADIR]=0x4000, [PAPAR]=0xFFFF
[PAODR]=0x0000, [PADAT]=0x29FE
Port B [PBDIR]=0x0FF0F, [PBPAR]=0x0600E
[PBODR]=0x00000, [PBDAT]=0x3631D
Port C [PCDIR]=0x00C, [PCPAR]=0x000
[PCSO]=0xBA0, [PCDAT]=0xFC0, [PCINT]=0x00F
Receive Ring
rmd(68012A70): status 9000 length 60C address 1DCD604
rmd(68012A78): status 9000 length 60C address 1DC8804
rmd(68012A80): status 9000 length 60C address 1DCDC84
rmd(68012A88): status 9000 length 60C address 1DD0A04
rmd(68012A90): status 9000 length 60C address 1DD2A84
rmd(68012A98): status 9000 length 60C address 1DD3784
rmd(68012AA0): status 9000 length 60C address 1DCE984
rmd(68012AA8): status 9000 length 60C address 1DC9B84
rmd(68012AB0): status 9000 length 60C address 1DD1704
rmd(68012AB8): status 9000 length 60C address 1DD3104
rmd(68012AC0): status 9000 length 60C address 1DD0384
rmd(68012AC8): status 9000 length 60C address 1DC9504
rmd(68012AD0): status 9000 length 60C address 1DCF684
rmd(68012AD8): status 9000 length 60C address 1DCF004
tx_limited=1(2)
SCC GENERAL PARAMETER RAM (at 0x68013F00)
Rx BD Base [RBASE]=0x2A70, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x2B30, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1548
Rx State [RSTATE]=0x0, BD Ptr [RBPTR]=0x2A70
Tx State [TSTATE]=0x0, BD Ptr [TBPTR]=0x2B30
SCC HDLC PARAMETER RAM (at 0x68013F38)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0
Nonmatch Addr Cntr [NMARC]=0
Retry Count [RETRC]=0
Max Frame Length [MFLR]=1608
Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=10945
User-defined Address 0000/0000/0000/0000
User-defined Address Mask 0x0000
buffer size 1524
PowerQUICC SCC specific errors:
153 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
328 aborted short frames
