Hello everybody, I am trying to get my Cisco 2811 to authenticate four DSL connections and load balance them by attaching the four DSL to a switch (each DSL going to a seperate VLAN) and then trunking all four VLAN's to a ethernet interface on the 2811. My issue, I can not get more than one DSL to authenticate at a time, for example Dialer1 will connect and then it will disconnect and Dialer2 will connect, etc... I have the modems in bridge mode and I am using seperate user/pass for each DSL account and I have verified that the user/pass are correct.
Below is my config from the router and a couple of messages that came across the console.
Can I even do what I am trying to accomplish?
Thanks,
Chris
*Apr 27 01:12:11.915: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1
*Apr 27 01:12:11.927: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
*Apr 27 01:12:11.931: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to down
*Apr 27 01:12:14.083: %DIALER-6-BIND: Interface Vi2 bound to profile Di2
*Apr 27 01:12:14.087: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
*Apr 27 01:12:14.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up
*Apr 27 01:12:32.139: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di2
*Apr 27 01:12:32.147: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
*Apr 27 01:12:32.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to down
*Apr 27 01:12:34.299: %DIALER-6-BIND: Interface Vi2 bound to profile Di1
*Apr 27 01:12:34.307: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
*Apr 27 01:12:34.459: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up
Router#show run
Building configuration...
Current configuration : 3648 bytes
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
dot11 syslog
ip source-route
!
!
ip cef
!
ip dhcp excluded-address 172.20.1.1
!
ip dhcp pool client
network 172.20.1.0 255.255.255.0
dns-server 8.8.8.8
default-router 172.20.1.1
!
!
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
!
!
!
!
!
!
!
voice-card 0
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO2811 sn FTX1041A1B5
username test privilege 15 secret 4 554Nq1aum3M01wRZ6FSR6rROZ6s/k8xo9EBYady0t6o
!
!
!
!
!
!
!
interface FastEthernet0/0
description LAN
ip address 172.20.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
duplex auto
speed auto
!
interface FastEthernet0/1.11
encapsulation dot1Q 11
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface FastEthernet0/1.12
encapsulation dot1Q 12
pppoe enable group global
pppoe-client dial-pool-number 2
!
interface FastEthernet0/1.13
encapsulation dot1Q 13
pppoe enable group global
pppoe-client dial-pool-number 3
!
interface FastEthernet0/1.14
encapsulation dot1Q 14
pppoe enable group global
pppoe-client dial-pool-number 4
!
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
ppp authentication chap pap callin
ppp chap hostname XXXX
ppp chap password 0 XXXX
ppp pap sent-username XXXX password 0 XXXX
!
interface Dialer2
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 2
ppp authentication chap pap callin
ppp chap hostname XXXX
ppp chap password 0 XXXX
ppp pap sent-username XXXX password 0 XXXX
!
interface Dialer3
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 3
ppp authentication chap pap callin
ppp chap hostname XXXX
ppp chap password 0 XXXX
ppp pap sent-username XXXX password 0 XXXX
!
interface Dialer4
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 4
ppp authentication chap pap callin
ppp chap hostname XXXX
ppp chap password 0 XXXX
ppp pap sent-username XXXX password 0 XXXX
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source route-map DIAL1 interface Dialer1 overload
ip nat inside source route-map DIAL2 interface Dialer2 overload
ip nat inside source route-map DIAL3 interface Dialer3 overload
ip nat inside source route-map DIAL4 interface Dialer4 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 0.0.0.0 0.0.0.0 Dialer2
ip route 0.0.0.0 0.0.0.0 Dialer3
ip route 0.0.0.0 0.0.0.0 Dialer4
!
access-list 1 permit 172.20.1.0 0.0.0.255
!
route-map DIAL1 permit 10
match ip address 1
match interface Dialer1
!
route-map DIAL2 permit 10
match ip address 1
match interface Dialer2
!
route-map DIAL3 permit 10
match ip address 1
match interface Dialer3
!
route-map DIAL4 permit 10
match ip address 1
match interface Dialer4
!
!
!
control-plane
!
!
!
!
mgcp profile default
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login local
transport input all
!
scheduler allocate 20000 1000
end
Router#
