Hello all,
I've got Cisco 877W but it didn't like when I applied what I think is the last firmware for ST Micro -
adsl_alc_20190_6.0.010.bin
Any suggestions?
Many thanks
Dan
My version:
#show ver
Cisco IOS Software, C870 Software (C870-ADVIPSERVICESK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Compiled Wed 21-Mar-12 00:53 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)YI3, RELEASE SOFTWARE
System returned to ROM by reload at 10:42:22 GMT Fri Mar 1 2002
System restarted at 13:58:35 BST Tue Oct 1 2013
System image file is "flash:c870-advipservicesk9-mz.151-4.M4.bin"
Last reload reason: Reload Command
Cisco 877W (MPC8272) processor (revision 2.0) with 236544K/25600K bytes of memory.
Processor board ID FCZ105123PM
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
1 Virtual Private Network (VPN) Module
1 802.11 Radio
128K bytes of non-volatile configuration memory.
53248K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
with the adsl_alc_20190_6.0.010.bin :
#show dsl int
ATM0
Alcatel 20190 chipset information
Line has not yet been activated.
Modem Status: Down (DMTDSL_DO_OPEN)
DSL Mode: Unknown
Interrupts: 37291 (0 spurious)
PHY Access Err: 0
Activations: 0
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR_6.0.010.bin
Operation FW: AMR-E-6.0.010.bin
FW Source: external
DSL: Training log buffer capability is not enabled
with the original 4.0.015 firware:
#show dsl int
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.3 (ADSL2) Annex A
ITU STD NUM: 0x03 0x2
Chip Vendor ID: 'STMI' 'IFTN'
Chip Vendor Specific: 0x0000 0x71C8
Chip Vendor Country: 0x0F 0xB5
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x0000 0x0000
Modem Vendor Country: 0xB5 0x00
Serial Number Near: FCZ105123P 877W-G-E 15.1
Serial Number Far: Chip ID: C196 (0)
DFE BOM: DFE3.0 Annex A (1)
Capacity Used: 99% 100%
Noise Margin: 5.5 dB 6.0 dB
Output Power: 16.0 dBm 12.5 dBm
Attenuation: 61.0 dB 38.0 dB
FEC ES Errors: 0 0
ES Errors: 11 0
SES Errors: 1 0
LOSES Errors: 1 0
UES Errors: 0 43
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0xEB
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 4201 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-4.0.015_no_bist.bin
Operation FW: AMR-4.0.015.bin
FW Source: embedded
FW Version: 4.0.15
