cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3434
Views
0
Helpful
27
Replies

Cisco 1130ag Access Point Image Upgrade

humair.amil
Level 1
Level 1

Hi all,

I was just trying to upgrade my first cisco access point at home. I am a bit lost...

a) I can't run "conf t" command.

b) It seems to have ver 3 or ver 4 lwapp image running on it.

c) keeps rebooting itself when it starts up and says "certificate is invalid"

I am attaching some screenshots, if you could have a look when you have a minute and guide me in the right direction then I will be highly grateful to you.

Thanks.

show ver.PNGflash.PNG

27 Replies 27

Leo Laohoo
Hall of Fame
Hall of Fame

What are you trying to do?

Your AP is running controller-based IOS (RCV) and the only way for you to upgrade this firmware is when you upgrade the firmware of the controller.

When you upgrade the firmware of the controller, the controller will determine if the APs attached to the controller should synchronize their firmware with the controller or not.  If they do, the controller will push the correct firmware to the APs.

I am trying to upgrade the AP so that it uses 7.3 LWAPP image version. I need to run that so that it could connect to the Cisco Virtual Wireless LAN Controller.

My Cisco vWLC is already on the 7.4 version but the Access Points still fails to connect to it or download image from it.

I am trying to upgrade the AP so that it uses 7.3 LWAPP image version. I need to run that so that it could connect to the Cisco Virtual Wireless LAN Controller.

No you don't. 

Let the AP join the WLC and the WLC will take care of the firmware of the AP.

Leo,

The AP keeps rebooting itself. The WLC picks it up for a second but looses it again. On the AP console I can see errorr messages "Certificate is not valid" etc.

I will try and post the screen shot of error message that it is giving me.

So this is the error that I get. The AP reboots everytime after displaying that error message.

"No more AP Manager IP Addresses remaining" is the vital error message.

How many APs can your WLC support and how many are currently registered?

Post the following command outputs:

1.  WLC:  sh sysinfo;

2.  WLC:  sh time;

3.  AP:  sh version; and

4.  AP:  sh inventory

PS:  Don't post screenshots.  Copy-and-paste the result here or in a notepad. 

Show Sysinfo on WLC

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.4.100.60

RTOS Version..................................... 7.4.100.60

Bootloader Version............................... 7.4.100.60

Emergency Image Version.......................... 7.4.100.60

Build Type....................................... DATA + WPS

System Name...................................... Cisco_b9:b6:23

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1631

IP Address....................................... 192.168.1.240

System Up Time................................... 4 days 1 hrs 5 mins 52 secs

System Timezone Location.........................

System Stats Realtime Interval................... 5

System Stats Normal Interval..................... 180

Configured Country............................... US  - United States

--More-- or (q)uit

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 1

Number of Active Clients......................... 0

Memory Current Usage............................. Unknown

Memory Average Usage............................. Unknown

CPU Current Usage................................ Unknown

CPU Average Usage................................ Unknown

Burned-in MAC Address............................ 00:0C:29:B9:B6:23

Maximum number of APs supported.................. 200

Show Time on WLC

Time............................................. Tue Jun 18 00:03:26 2013

Timezone delta................................... 0:0

Timezone location................................

NTP Servers

    NTP Polling Interval.........................     3600

     Index     NTP Key Index     NTP Server      NTP Msg Auth Status

    -------  ---------------------------------------------------------------

       1              0       81.168.77.149       AUTH DISABLED

Show ver on AP

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEA                                                                             SE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:38 by alnguyen

ROM: Bootstrap program is C1130 boot loader

BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (                                                                             fc2)

144AP1 uptime is 7 minutes

System returned to ROM by reload

System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"

cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/81                                                                             92K bytes of memory.

Processor board ID FCZ1225Q1JN

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from reload

LWAPP image version 3.0.51.0

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:1E:F7:EE:58:76

Part Number                          : 73-8962-12

PCA Assembly Number                  : 800-24818-11

PCA Revision Number                  : B0

PCB Serial Number                    : FOC12230B10

Top Assembly Part Number             : 800-29144-02

Top Assembly Serial Number           : FCZ1225Q1JN

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1131AG-E-K9

Show Inventory on AP

does not produce any results.

Thanks

Configured Country............................... US  - United States

Your WLC is configured for the US, regulatory domain of "-A".

Product/Model Number                 : AIR-LAP1131AG-E-K9

Your AP has a regulatory domain of Europ, "-E".

These are the main reasons why your AP won't join the WLC.

Exactly WHERE are you planning to install the AP?  What country?

I am going to deploy it in the UK. Just trying to build a home lab to practice before taking the CCNA Wireless exam.

How would I change this on the Controller to match the AP settings?

Thank you for your help.

Wireless > Country

Leo,

Sorry for the late reply. I have made changes as advised by yourself but I am still getting the same error message. Could you please help?

Regards,

Humair

Console into the AP and reboot the AP.

Post the entire bootup process.

144AP1#reload

%Reload in progress

144AP1#Xmodem file system is available.

flashfs[0]: 8 files, 3 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 15998976

flashfs[0]: Bytes used: 5496832

flashfs[0]: Bytes available: 10502144

flashfs[0]: flashfs fsck took 27 seconds.

Base ethernet MAC Address: 00:1e:f7:ee:58:76

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################

File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:38 by alnguyen

Image text-base: 0x00003000, data-base: 0x0035E440

Initializing flashfs...

flashfs[1]: 8 files, 3 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15998976

flashfs[1]: Bytes used: 5496832

flashfs[1]: Bytes available: 10502144

flashfs[1]: flashfs fsck took 3 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.

Processor board ID FCZ1225Q1JN

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from reload

LWAPP image version 3.0.51.0

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:1E:F7:EE:58:76

Part Number                          : 73-8962-12

PCA Assembly Number                  : 800-24818-11

PCA Revision Number                  : B0

PCB Serial Number                    : FOC12230B10

Top Assembly Part Number             : 800-29144-02

Top Assembly Serial Number           : FCZ1225Q1JN

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1131AG-E-K9

Press RETURN to get started!

*Mar  1 00:00:06.072: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source

*Mar  1 00:00:06.078: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:38 by alnguyen

*Mar  1 00:00:07.034: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar  1 00:00:08.034: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down

*Mar  1 00:00:16.033: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

*Mar  1 00:00:25.097: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Mar  1 00:00:36.499: LWAPP_CLIENT_ERROR_DEBUG: spamHandleDiscoveryTimer : Found the discovery response from MASTER Mwar

*Mar  1 00:00:36.508: %LWAPP-5-CHANGED: LWAPP changed state to JOIN

*Jun 21 22:43:12.002: LWAPP_CLIENT_ERROR_DEBUG:

*Jun 21 22:43:12.002: peer certificate verification failed

*Jun 21 22:43:12.002: LWAPP_CLIENT_ERROR_DEBUG: spamDecodeJoinReply : Certificate is not valid

*Jun 21 22:43:12.002: LWAPP_CLIENT_ERROR_DEBUG: Unable to decode join reply

*Jun 21 22:43:16.980: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response

*Jun 21 22:43:16.980: LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP addresses remain.

*Jun 21 22:43:17.017: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.

*Jun 21 22:43:17.017: %LWAPP-5-CHANGED: LWAPP changed state to DOWN

Can you post the output to the WLC command: sh sysinfo

Sent from Cisco Technical Support Nintendo App

Review Cisco Networking for a $25 gift card