configuration NAT overload for ASA 5525

[MohammadSalih]

hi every one ,

i want to configure NAT over load

i have one public ip address 37.x.x.x

and pool of private ip addresses 70.70.x.x

when i configure natting by typing

nat (inside,outside) soure (static or dynamic) ,

there is no PAT configuration , because i want every private IPs share one public ip.

[MHM Cisco World]

nat (inside,outside) source dynamic any interface <<<- I use this for NAT overload 

[paul driver]

Hello @MHM Cisco World 
FYI
nat (inside,outside) source dynamic any interface =  Section 1
nat (inside,outside) after-auto source dynamic any interface  = Section 3

[MHM Cisco World]

both are NAT overload 
after-auto just change the orde of NAT not change the NAT type.

[paul driver]

Hello
What im trying to allude to is you wouldn't want dynamic PAT (overload) to be in section 1, its a catch all statement as such if you need to append additional statements then you would have to re-order the NAT to accommodate , so would say its recommended to use section 3.

[Georg Pauwen]

Hello,

post the full running configuration (sh run) of your ASA.

[MohammadSalih]

thanks for replying

interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 37.X.X.194 255.255.255.248

interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 70.70.2.1 255.255.255.0

interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 70.70.3.1 255.255.255.0

object network public_LAN1
host 37.X.X.195
object network public_LAN2
host 37.X.X.196

object-group network private_LAN1
network-object 70.70.2.0 255.255.255.0
object-group network private_LAN2
network-object 70.70.3.0 255.255.255.0

(just missing the NAT/PAT command)

[paul driver]

Hello

ASA NAT/PAT you can apply it two ways:
Manual NAT (globally) or  Auto NAT (under an object)

It also has 3 sections (Default 1)
Manual NAT can be set in Section 1 or 3 (after auto) 
Auto NAT = Section 2.

These sections are checked in order (1,2,3)
Manual
Auto
After Auto

Lastly in each section the nat rules are ordered sequentially just like within an access-list.

Can you post the following.
sh run nat
sh nat
sh run object
sh run object-group
sh run access-list
sh run access-group

Also perform a packet tracer and post the output.
packet-tracer input INSIDE tcp < lan ip> 12345 <internet ip> 80 

[MohammadSalih]

thanks for replying

interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 37.X.X.194 255.255.255.248

interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 70.70.2.1 255.255.255.0

interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 70.70.3.1 255.255.255.0

object network public_LAN1
host 37.X.X.195
object network public_LAN2
host 37.X.X.196

object-group network private_LAN1
network-object 70.70.2.0 255.255.255.0
object-group network private_LAN2
network-object 70.70.3.0 255.255.255.0

(just missing the NAT/PAT command)

[MHM Cisco World]

then just add NAT as I mention above. 
good luck friend 

[MohammadSalih]

thanks alot for help,

i will apply this command (nat (inside,outside) source dynamic any interface) as you mentioned me,

but how to Control NATTING transluations

over more than one public?

i want 70.70.2.0/24 goes to 37.X.X.195

and

70.70.3.0/24 goes to 37.X.X.196

how can i deploy it in nat command?

[MHM Cisco World]

I will share lab with you tonight.

[MohammadSalih]

thanks alot .

[paul driver]

Hello

---

@MohammadSalih wrote:

over more than one public?

i want 70.70.2.0/24 goes to 37.X.X.195

and

70.70.3.0/24 goes to 37.X.X.196

how can i deploy it in nat command?

---

object network Inside_1
Subnet 70.70.2.0 255.255.255.0

object network outside1
host 37.X.X.195

object network Inside_2
subnet 70.70.2.0 255.255.255.0

object network outside2
host 37.X.X.196

nat (inside,outside)  1source dynamic Inside_1 outside1
nat (inside,outside)  2 source dynamic Inside_2 outside2
nat (inside,outside) after-auto source dynamic any interface

[MohammadSalih]

i will try it.

thanks very much.