cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
494
Views
0
Helpful
3
Replies
Highlighted
Participant

DMVPN - HSRP - EIGRP Issues

I'm currently in the process of a mass DMVPN deployment. Right now, we have a single HUB and a few sites are slated to have DUAL SPOKE.

HUB

Cisco 2951

Spoke 

R1 - Cisco 2911

R2 - Cisco 2911

HSRP w/ IP SLA Tracking between R1 and R2

 

I have tunnels on each of the above Spoke Routers pointing to the Tunnel interface at the HUB. Traffic and EIGRP are working as expected on R1. 

When R1 is rebooted, R2 takes over the virutal IP and becomes the active HSRP router; however, routes are removed from the HUB and R2 never learns about them / passes traffic. 

 

HUB Config: 

interface Tunnel0
 description DMVPN Tunnel
 ip address 172.16.1.1 255.255.255.0
 no ip redirects
 no ip next-hop-self eigrp 50
 no ip split-horizon eigrp 50
 ip nhrp authentication firewall
 ip nhrp map multicast dynamic
 ip nhrp network-id 1
 tunnel source 1.1.1.1
 tunnel mode gre multipoint
 tunnel protection ipsec profile protect-gre

router eigrp 50
 network 10.0.0.0
 network 172.16.0.0
 network 172.16.1.1 0.0.0.0
 network 192.168.0.0
 redistribute eigrp 11

 

SPOKE R1 Config

interface Tunnel0
 description DMVPN Tunnel
 ip address 172.16.1.17 255.255.255.0
 no ip redirects
 ip nhrp authentication firewall
 ip nhrp map multicast dynamic
 ip nhrp map multicast 1.1.1.1
 ip nhrp map 172.16.1.1 1.1.1.1
 ip nhrp network-id 1
 ip nhrp nhs 172.16.1.1
 ip virtual-reassembly in
 tunnel source GigabitEthernet0/0
 tunnel mode gre multipoint
 tunnel protection ipsec profile protect-gre

 

 

interface GigabitEthernet0/1.17
 description LAN
 encapsulation dot1Q 17
 ip address 10.96.17.253 255.255.255.0
 ip access-group OUTBOUND in
 ip flow ingress
 ip flow egress
 ip nat inside
 ip virtual-reassembly in
 standby 0 ip 10.96.17.254
 standby 0 priority 110
 standby 0 preempt
 standby 0 track 1 decrement 20

 

router eigrp 50
 network 10.96.17.0 0.0.0.255
 network 172.16.1.17 0.0.0.0
 network 192.168.17.0
 redistribute static route-map STATICS

SPOKE R2 Config

interface Tunnel0
 description DMVPN Tunnel
 ip address 172.16.1.16 255.255.255.0
 no ip redirects
 ip nhrp authentication firewall
 ip nhrp map multicast dynamic
 ip nhrp map multicast 1.1.1.1
 ip nhrp map 172.16.1.1 1.1.1.1
 ip nhrp network-id 1
 ip nhrp nhs 172.16.1.1
 ip virtual-reassembly in
 tunnel source GigabitEthernet0/0
 tunnel mode gre multipoint
 tunnel protection ipsec profile protect-gre

interface GigabitEthernet0/1.17
 description LAN
 encapsulation dot1Q 17
 ip address 10.96.17.252 255.255.255.0
 ip access-group OUTBOUND in
 ip flow ingress
 ip flow egress
 ip nat inside
 ip virtual-reassembly in
 standby 0 ip 10.96.17.254
 standby 0 preempt
 standby 0 track 1 decrement 20

router eigrp 50
 network 10.96.17.0 0.0.0.255
 network 172.20.1.16 0.0.0.0

 

 

 

 

 

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Master

The biggest issue that I see

The biggest issue that I see here is that on R2 there is no network statement in EIGRP to get the routing protocol to run over the tunnel. You need something that might look somewhat like this

 network 172.16.1.16 0.0.0.0

 

HTH

 

Rick

3 REPLIES 3
Hall of Fame Master

The biggest issue that I see

The biggest issue that I see here is that on R2 there is no network statement in EIGRP to get the routing protocol to run over the tunnel. You need something that might look somewhat like this

 network 172.16.1.16 0.0.0.0

 

HTH

 

Rick

Participant

Thanks Rick - a good reminder

Thanks Rick - a good reminder is that sometimes typing 172.20 instead of 172.16 can cause all kinds of pain! :) 

Hall of Fame Master

Yes sometimes it is those

Yes sometimes it is those very small details that cause all kinds of pain and sometimes take a fresh pair of eyes to find. Glad I could help. Thank you for using the rating system to mark this question as answered.

 

HTH

 

Rick

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards