cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3443
Views
0
Helpful
3
Replies

Installation a new IOS for a new 7606-S

Hello Dear,

I have a fresh piece of 7606-S router, i am planing to install a new IOS ( 15.2.4S or 12.2.33-SRD8 ) ...

SIP-200 / RSP720 moduls ... would ypu plese provides me a configuration guide for installing IOS for 7600 serise router ...

I have the image on TFTP server .. what shai do ? it will be helpful if you guide step by step ..

your reply is highly appreciated..

Regards,

Ahmed

1 Accepted Solution

Accepted Solutions

Ivan Shirshin
Cisco Employee
Cisco Employee


Hi,

Since you have SIP, you also have to upgrade FPD:

http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html#wp1063108http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html#wp1063119http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html#wp1063130

1. Copy the IOS Image and corresponding FPD package from CCO to the flash card. You can insert it to one of working routers and copy from TFTP server.

2. Put the flash card into disk0 slot on new RSP. Connect on console.

3. Boot the router.

4. If it falls into ROMMON, run:

     confreg 0x2102

     sync

     boot disk0:

5. When the IOS is booted, copy FPD package and IOS file to the sup-bootdisk or bootflash (check the flash size to ensure it is enough to hold both files).

     show sup-bootdisk:

     show bootflash:

     copy disk0: sup-bootdisk:

     copy disk0: sup-bootdisk:

6. Change the boot string:

     conf t

          config-reg 0x2102

          boot system flash sup-bootdisk:

          end

     wr

7. Reload to boot with new image and make sure everything works fine.

8. Check the modules status and image version:

     show version

     show module

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

View solution in original post

3 Replies 3

Ivan Shirshin
Cisco Employee
Cisco Employee


Hi,

Since you have SIP, you also have to upgrade FPD:

http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html#wp1063108http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html#wp1063119http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html#wp1063130

1. Copy the IOS Image and corresponding FPD package from CCO to the flash card. You can insert it to one of working routers and copy from TFTP server.

2. Put the flash card into disk0 slot on new RSP. Connect on console.

3. Boot the router.

4. If it falls into ROMMON, run:

     confreg 0x2102

     sync

     boot disk0:

5. When the IOS is booted, copy FPD package and IOS file to the sup-bootdisk or bootflash (check the flash size to ensure it is enough to hold both files).

     show sup-bootdisk:

     show bootflash:

     copy disk0: sup-bootdisk:

     copy disk0: sup-bootdisk:

6. Change the boot string:

     conf t

          config-reg 0x2102

          boot system flash sup-bootdisk:

          end

     wr

7. Reload to boot with new image and make sure everything works fine.

8. Check the modules status and image version:

     show version

     show module

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

Hello my dear Ivan,

as usual your explanation is wonderful, i will install and i will let you know how things are.

Thanking you.

Regards,

Ahmed

Welcome, Ahmed.

Kind Regards,
Ivan
Review Cisco Networking products for a $25 gift card