Please check If I am missing something. Few questions on top of my mind.1. There is dedicated port called CMP-mgmt. Should I configure it and use during my upgrade like OOB mgmt?2. What is an EPLD image? Should I upgrade these also.
Hello.We have 4 switches C3560 running EIGRP. We have PBR in one of them in this way:interface FastEthernet0/22 no switchport ip address 192.168.224.66 255.255.255.192 ip policy route-map wbcnvuemb16 load-interval 30 delay 50000 no snmp trap link-sta...
Hi,We are facing problem with load sharing between two intranet links connected to a Cisco Layer 3 switch. I am thinking of using "ip cef load-sharing algorithm universal ID" command to fix this problem. As per my knowledge Universal logic is the fea...
Hi guys,Need you all opinion..Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 551...
Hi guysWe have recently been dealing with a situation where we get the above packets and access to one of our applications just hangs.To tell you a bit about our network, hub and spoke topology, with IPSEC GRE tunnels over MPLS, and the application s...
The setup is a S2S VPN with failover to 3G HWIC in a Cisco 1941 however the IPSEC tunnel needs to remain up through 3G if ADSL fails.The failover works ok, however when plugging ADSL back in, the - "sh crypto session" shows both dialer 0, and dialer ...
I am looking for a simple router recomendation for multihoming dual 100Mbps internet connections with BGP routing. What are the current best practices regarding required resources for the full Internet BGP routing table? We were thinking of specing...
hi,i am trying to enable packet capture using the instructions found at Router IP Traffic Export Packet Capture Enhancements. i have managed all the instructions except towards the end. when i type:Router#traffic-export interface fasteth0/0 clear ...
Anyone know the difference between The 'p' softwareLike c7200p-fpd-pkg.124-24.T7.pkgc7200p-kboot-mz.124-24.T7.binc7200p-advipservicesk9-mz.124-24.T7.binand the software without the 'p'c7200-boot-mz.124-24.T7.binc7200-kboot-mz.124-2...
Hi,When i configure subinterfaces on trunk interfaces which are located on Routers, What is the default packet queing rule for subinterfaces? Is there any configuration to make a subinterfcace has strick proirty than others?
Dear Sirs!Now, I use Catalyst WS-C3750G-12S-S as BGP router. But it is switch do not support in higher 65535 (32 bit asn).In future, I plan to use two or three ISP (each will be connected through 1Gb uplink).I need a router, who will be support 32 bi...
Is it possible to have two ISP connection internet load balancing? We are having two different ISP's internet connection (20 Mbps & 8 Mbps) for the internet but we are using only one for internet and for site-to-site VPN.But what we need is to use on...
Dears,I have two ISP need to connect them on my router.The Router that I have is 2811 where it contains two Fa ports only, so I put an access switch between the two ISPs and the Fa0/0 then configured the Interface Fa0/0 with two IPs ISP1 and ISP2 as ...
Hi,i am trying to get my hands dirty with mGRE. Please check the attached image. It a fairly basic scenario. R2 as the hub and R4 as a branch router. The eigrp neighborship between the two tunnel interfaces is not coming up. If I configure "tunnel de...
