05-10-2017 12:49 AM - edited 03-05-2019 08:30 AM
Hello,
I don't know why, but I'm not able to ping my ESXi server from another VLAN.
Any
Here is my config:
!
interface FastEthernet0
description * LINK TO THOMAS PC *
switchport access vlan 205
switchport priority extend trust
no ip address
spanning-tree portfast
!
interface FastEthernet1
description * LINK TO SW01.HOME.LAB *
switchport trunk allowed vlan 1,101,1001-1005
switchport mode trunk
no ip address
!
interface FastEthernet2
no ip address
shutdown
!
interface FastEthernet3
description * LINK TO ESXI01 *
switchport access vlan 101
switchport priority extend trust
no ip address
spanning-tree portfast
!
interface FastEthernet4
description * LINK TO GW *
ip address dhcp
duplex auto
speed auto
!
interface Vlan1
no ip address
!
interface Vlan101
ip address 10.0.1.3 255.255.255.0
!
interface Vlan205
ip address 192.168.5.254 255.255.255.0
!
Here is the output of a "show
Gateway of last resort is 192.168.190.1 to network 0.0.0.0
S* 0.0.0.0/0 [254/0] via 192.168.190.1
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.0.1.0/24 is directly connected, Vlan101
L 10.0.1.3/32 is directly connected, Vlan101
192.168.5.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.5.0/24 is directly connected, Vlan205
L 192.168.5.254/32 is directly connected, Vlan205
192.168.190.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.190.0/24 is directly connected, FastEthernet4
L 192.168.190.196/32 is directly connected, FastEthernet4
Here is the output of a "show
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES unset up up
FastEthernet1 unassigned YES unset down down
FastEthernet2 unassigned YES unset administratively down down
FastEthernet3 unassigned YES unset up up
FastEthernet4 192.168.190.196 YES DHCP up up
Vlan1 unassigned YES unset down down
Vlan101 10.0.1.3 YES manual up up
Vlan205 192.168.5.254 YES manual up up
I can ping my ESXi (IP 10.0.1.2) connected to Fa3 from
router01#ping 10.0.1.2 source vlan 101
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.1.2, timeout is 2 seconds:
Packet sent with a source address of 10.0.1.3
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 msrouter01#ping 10.0.1.2 source vlan 205
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.1.2, timeout is 2 seconds:
Packet sent with a source address of 192.168.5.254
.....
Success rate is 0 percent (0/5)
What can I do to solve this issue?
Thanks in advance for your reply,
Thomas.
Solved! Go to Solution.
05-10-2017 01:25 AM
check default gateway on 10.0.1.2
05-10-2017 01:25 AM
check default gateway on 10.0.1.2
05-10-2017 08:03 AM
Yes correct.
gateway on server should be Vlan's interface IP
Mask should also match with Vlan
05-10-2017 09:42 PM
Indeed, it was the gateway....
Thanks for your investigation
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide