cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1166
Views
0
Helpful
1
Replies

PPP Multilink config

richreitenauer
Level 1
Level 1

Hi,

New user here.  I think I have my PPP multilink setup correctly.  Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card.  One AL light is on at each location.  Though I checked with my ISP and they said it was my network cables as everything looked good on their end.  Currently one T1 circuit is connected at each end so users do not see a disruption.  This is a new install with two routers and the config is shown below.

Router 1-----

controller T1 0/0/0

cablelength long 0db

channel-group 0 timeslots 1-24

!

controller T1 0/0/1

cablelength long 0db

channel-group 0 timeslots 1-24

!

interface Multilink1

ip address 192.168.200.1 255.255.255.252

ppp multilink

ppp multilink group 1

ppp multilink fragment disable

no cdp enable

!

interface Serial0/0/0:0 --- Connection that is inactive

no ip address

encapsulation ppp

ppp multilink

ppp multilink group 1

no fair-queue

!

interface Serial0/0/1:0

no ip address

encapsulation ppp

ppp multilink

ppp multilink group 1

no fair-queue

Sh PPP Multilink

  Bundle up for 00:19:36, total bandwidth 1536, load 1/255

  Receive buffer limit 12000 bytes, frag timeout 1000 ms

    0/0 fragments/bytes in reassembly list

    0 lost fragments, 0 reordered

    0/0 discarded fragments/bytes, 0 lost received

    0x0 received sequence, 0x0 sent sequence

  Member links: 1 active, 1 inactive (max 255, min not set)

    Se0/0/1:0, since 00:19:36

    Se0/0/0:0 (inactive)

Router 2-------

controller T1 0/0/0

cablelength long 0db

channel-group 0 timeslots 1-24

!

controller T1 0/0/1

cablelength long 0db

channel-group 0 timeslots 1-24

!

ip ssh version 2

!

!

!

!

interface Multilink1

ip address 192.168.200.2 255.255.255.252

ppp multilink

ppp multilink group 1

ppp multilink fragment disable

no cdp enable

!

interface GigabitEthernet0/0

ip address 10.95.1.1 255.255.254.0

ip helper-address 10.10.7.13

duplex auto

speed auto

!

interface Serial0/0/0:0---Connection is working

no ip address

encapsulation ppp

ppp multilink

ppp multilink group 1

no fair-queue

!

interface Serial0/0/1:0----INactive

no ip address

encapsulation ppp

ppp multilink

ppp multilink group 1

no fair-queue

sh ppp multilink

  Bundle up for 00:22:42, total bandwidth 1536, load 1/255

  Receive buffer limit 12000 bytes, frag timeout 1000 ms

    0/0 fragments/bytes in reassembly list

    0 lost fragments, 0 reordered

    0/0 discarded fragments/bytes, 0 lost received

    0x0 received sequence, 0x0 sent sequence

  Member links: 1 active, 1 inactive (max 255, min not set)

    Se0/0/0:0, since 00:22:42

    Se0/0/1:0 (inactive)

No inactive multilink interfaces   Bundle up for 00:22:42, total bandwidth 1536, load 1/255
  Receive buffer limit 12000 bytes, frag timeout 1000 ms
    0/0 fragments/bytes in reassembly list
    0 lost fragments, 0 reordered
    0/0 discarded fragments/bytes, 0 lost received
    0x0 received sequence, 0x0 sent sequence
  Member links: 1 active, 1 inactive (max 255, min not set)
    Se0/0/0:0, since 00:22:42
    Se0/0/1:0 (inactive)
No inactive multilink interfaces

1 Reply 1

paolo bevilacqua
Hall of Fame
Hall of Fame

Likely faulty circuit (despite whatever telco may say).

Take "show controllers T1".

Review Cisco Networking for a $25 gift card