06-16-2011 01:42 PM - edited 03-04-2019 12:44 PM
Hi,
New user here. I think I have my PPP multilink setup correctly. Though I am getting AL lights on one of my connections via a VWIC2-2MFT-T1/E1 card. One AL light is on at each location. Though I checked with my ISP and they said it was my network cables as everything looked good on their end. Currently one T1 circuit is connected at each end so users do not see a disruption. This is a new install with two routers and the config is shown below.
Router 1-----
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
!
controller T1 0/0/1
cablelength long 0db
channel-group 0 timeslots 1-24
!
interface Multilink1
ip address 192.168.200.1 255.255.255.252
ppp multilink
ppp multilink group 1
ppp multilink fragment disable
no cdp enable
!
interface Serial0/0/0:0 --- Connection that is inactive
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 1
no fair-queue
!
interface Serial0/0/1:0
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 1
no fair-queue
Sh PPP Multilink
Bundle up for 00:19:36, total bandwidth 1536, load 1/255
Receive buffer limit 12000 bytes, frag timeout 1000 ms
0/0 fragments/bytes in reassembly list
0 lost fragments, 0 reordered
0/0 discarded fragments/bytes, 0 lost received
0x0 received sequence, 0x0 sent sequence
Member links: 1 active, 1 inactive (max 255, min not set)
Se0/0/1:0, since 00:19:36
Se0/0/0:0 (inactive)
Router 2-------
controller T1 0/0/0
cablelength long 0db
channel-group 0 timeslots 1-24
!
controller T1 0/0/1
cablelength long 0db
channel-group 0 timeslots 1-24
!
ip ssh version 2
!
!
!
!
interface Multilink1
ip address 192.168.200.2 255.255.255.252
ppp multilink
ppp multilink group 1
ppp multilink fragment disable
no cdp enable
!
interface GigabitEthernet0/0
ip address 10.95.1.1 255.255.254.0
ip helper-address 10.10.7.13
duplex auto
speed auto
!
interface Serial0/0/0:0---Connection is working
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 1
no fair-queue
!
interface Serial0/0/1:0----INactive
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 1
no fair-queue
sh ppp multilink
Bundle up for 00:22:42, total bandwidth 1536, load 1/255
Receive buffer limit 12000 bytes, frag timeout 1000 ms
0/0 fragments/bytes in reassembly list
0 lost fragments, 0 reordered
0/0 discarded fragments/bytes, 0 lost received
0x0 received sequence, 0x0 sent sequence
Member links: 1 active, 1 inactive (max 255, min not set)
Se0/0/0:0, since 00:22:42
Se0/0/1:0 (inactive)
No inactive multilink interfaces Bundle up for 00:22:42, total bandwidth 1536, load 1/255
Receive buffer limit 12000 bytes, frag timeout 1000 ms
0/0 fragments/bytes in reassembly list
0 lost fragments, 0 reordered
0/0 discarded fragments/bytes, 0 lost received
0x0 received sequence, 0x0 sent sequence
Member links: 1 active, 1 inactive (max 255, min not set)
Se0/0/0:0, since 00:22:42
Se0/0/1:0 (inactive)
No inactive multilink interfaces
06-16-2011 11:12 PM
Likely faulty circuit (despite whatever telco may say).
Take "show controllers T1".
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide