05-29-2007 02:55 PM - edited 03-03-2019 05:12 PM
My router doesn't seem to be passing traffic. I have a static route set, but it's not working. I'm new to router configuration, can someone help?
05-29-2007 02:59 PM
Post your (sanitized) config, the router model, and the version of IOS you're using.
It may also be useful to know who/what's in the other side and beyond.
Thanks
Scott
05-29-2007 03:12 PM
Here is my configuration:
pe-coc-connect>
pe-coc-connect>
pe-coc-connect>show ver
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 25-Oct-05 17:10 by evmiller
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
pe-coc-connect uptime is 1 hour, 49 minutes
System returned to ROM by power-on
System image file is "flash:c1841-ipbase-mz.124-1c.bin"
Cisco 1841 (revision 7.0) with 114688K/16384K bytes of memory.
Processor board ID FTX1118Z01P
2 FastEthernet interfaces
1 Serial interface
WIC T1-DSU
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31360K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2142
pe-coc-connect>
pe-coc-connect>
pe-coc-connect#show run
Building configuration...
Current configuration : 925 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname pe-coc-connect
!
boot-start-marker
boot-end-marker
!
enable secret xxx
enable password *****
!
no aaa new-model
!
resource policy
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
snmp-timeout 180
ip subnet-zero
no ip routing
no ip cef
!
!
no ip dhcp use vrf connected
!
!
!
!
!
!
interface FastEthernet0/0
ip address 192.168.1.254 255.255.255.0
no ip route-cache
speed auto
half-duplex
no mop enabled
!
interface FastEthernet0/1
no ip address
no ip route-cache
shutdown
duplex auto
speed auto
!
interface Serial0/0/0
ip address 10.111.248.14 255.255.255.248
encapsulation ppp
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.111.248.9
!
ip http server
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
password *****
login
!
end
pe-coc-connect#
05-29-2007 03:41 PM
The reason is
NO IP ROUTING
also there are no NAT statements present for 192.168.1.0/24 Network.
Muhammad
05-29-2007 03:56 PM
It's hard for a router to route when is told "no ip routing" :)
HX2 -- This is a jokeful remark and wish you good luck, do not hesitate to ask further questions once you have made the necessary config adjusts.
05-29-2007 04:51 PM
Hi
Put ip routing in configuration ,i beliave after that everthing is working, let me know if you face any problem.
-Minuj
05-29-2007 05:22 PM
something like:
ip route 0.0.0.0 0.0.0.0 s0/0/0
is that what is missing....
05-29-2007 05:26 PM
As i indicated earlier, If you look at the config you have sent, it has a statement
NO IP ROUTING
which is preventing your route to route the traffic.
0.0.0.0 0.0.0.0 is the default route for all traffic which is already present.
05-29-2007 09:03 PM
Hi ,
go to config mode and issue the following command .
(config)#ip routing.
check whether the traffice is flowing or not after enabling ip routing.
Thanks,
Satish
05-30-2007 08:47 AM
Thanks....
That worked...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide