12-28-2019 04:08 AM
Hi,
I am trying to use a Cisco 1841 router to make a connection between two separate LANs which are directly connected.
FastEthernet 0/0 is connected to network 10.80.1.0/24 and the interface received IP 10.80.1.135 IP via DHCP from a router on this network (a TP-Link router at 10.80.1.1)
FastEthernet 0/1 is network 192.168.0.0/24 and I want the 1841 router to provide DHCP.
What is required to make these two networks able to communicate with each other?
How can I allow clients on the 192.168.0.0 network to access the internet using my TP-Link router at 10.80.1.1?
I am very new to Networking and I am currently studying for CCNA R&S so any advice would be very much appreciated.
Router#show ip int br Interface IP-Address OK? Method Status Protocol FastEthernet0/0 10.80.1.135 YES DHCP up up FastEthernet0/1 192.168.0.1 YES manual up up Serial0/0/0 unassigned YES unset administratively down down Router#
Building configuration... Current configuration : 928 bytes ! ! Last configuration change at 11:34:32 UTC Sat Dec 28 2019 ! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ip source-route ! ! ip dhcp excluded-address 192.168.0.1 192.168.0.50 ! ip dhcp pool Floor1 network 192.168.0.0 255.255.255.0 default-router 192.168.0.1 dns-server 192.168.0.1 ! ! ip cef multilink bundle-name authenticated ! ! license udi pid CISCO1841 sn FCZ151294GL ! ! ! ! ! ! interface FastEthernet0/0 ip address dhcp duplex auto speed auto ! interface FastEthernet0/1 ip address 192.168.0.1 255.255.255.0 duplex auto speed auto ! interface Serial0/0/0 no ip address shutdown clock rate 2000000 ! ip forward-protocol nd ! ! no ip http server ! ! ! control-plane ! ! line con 0 line aux 0 line vty 0 4 login ! scheduler allocate 20000 1000 end
Router#show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, + - replicated route Gateway of last resort is 10.80.1.1 to network 0.0.0.0 S* 0.0.0.0/0 [254/0] via 10.80.1.1 10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C 10.80.1.0/24 is directly connected, FastEthernet0/0 L 10.80.1.135/32 is directly connected, FastEthernet0/0 192.168.0.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.0.0/24 is directly connected, FastEthernet0/1 L 192.168.0.1/32 is directly connected, FastEthernet0/1
Thanks,
James
Solved! Go to Solution.
12-28-2019 06:04 AM - edited 12-28-2019 06:06 AM
Hello
It looks like you modem is already performing network translation for the 10.80.1.0/24 subnet
So you would need to NAT the 192.168.1.0/x subnet on the router so the users on this ip range would also be able to access the internet, and add a more specific static route than one you would have obtained via the dhcp from you modem,
int fa0/0
ip nat outside
int fa0/1
ip nat inside
access-list 10 permit 192.168.1.0 0.0.0.255
ip nat inside source list 10 interface fa0/0
ip route 0.0.0.0 0.0.0.0 fa0/0 dhcp
lastly you dhcp pool for the lan users should work as it is but if it doesn't then you have two options to either import the dhcp options from the modem into the dhcp pool or change the dns server to your isp dns or a public dns
ip dhcp pool Floor1
import all
no dns-server 192.168.0.1
or
ip dhcp pool Floor1
dns-server 8.8.8.8 8.8.8.4
12-28-2019 04:40 AM - edited 12-28-2019 04:57 AM
Can we have more information, what is the device connected from Router(interface FastEthernet0/1 ) to end device ? or Switch?
If the switch can we have the configuration of that.
if point to point link you can route a mutually static route, so each segment can communicate with each other.
ip route 0.0.0.0 0.0.0.0 FastEthernet 0/0
ip route 192.168.0.0 255.255.255.0 X/X (where the FAS 0/1 connect neighbour IP)
(TP Link also should have static route back to your router)
12-28-2019 06:04 AM - edited 12-28-2019 06:06 AM
Hello
It looks like you modem is already performing network translation for the 10.80.1.0/24 subnet
So you would need to NAT the 192.168.1.0/x subnet on the router so the users on this ip range would also be able to access the internet, and add a more specific static route than one you would have obtained via the dhcp from you modem,
int fa0/0
ip nat outside
int fa0/1
ip nat inside
access-list 10 permit 192.168.1.0 0.0.0.255
ip nat inside source list 10 interface fa0/0
ip route 0.0.0.0 0.0.0.0 fa0/0 dhcp
lastly you dhcp pool for the lan users should work as it is but if it doesn't then you have two options to either import the dhcp options from the modem into the dhcp pool or change the dns server to your isp dns or a public dns
ip dhcp pool Floor1
import all
no dns-server 192.168.0.1
or
ip dhcp pool Floor1
dns-server 8.8.8.8 8.8.8.4
12-30-2019 05:24 AM
Thanks for both the replies, I have managed to get this working with the below entries:
router(config)#access-list 1 permit 192.168.0.0 0.0.0.255 router(config)#ip nat inside source list 1 interface fastEthernet 0/0 overload router(config)# router(config)#int fa 0/1 router(config-if)#ip nat inside router(config)#int fa 0/0 router(config-if)#ip nat outside
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide