cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1878
Views
0
Helpful
2
Replies

SM-SRE-910-K9 ISR4351 Built-In SM controller

haydavis
Beginner
Beginner

Looking for assistance to get started configuring WAAS on a ISR4351 with built in SM controller.

I can not seem to find a interface to setup.  I tried playing with Service Engine interface but not getting anywhere. 

Interface              IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0/0   unassigned      YES NVRAM  up                    up     
Gi0/0/0.986            <removed>    YES manual up                    up     
GigabitEthernet0/0/1   <removed>    YES manual up                    up     
GigabitEthernet0/0/2   unassigned      YES NVRAM  up                    up     
Gi0/0/2.35             <removed>  YES NVRAM  up                    up     
Service-Engine0/1/0    unassigned      YES unset  up                    up     
Serial0/1/0:0          unassigned      YES unset  down                  down   
Serial0/1/0:1          unassigned      YES unset  down                  down   
Serial0/1/0:2          unassigned      YES unset  down                  down   
Serial0/1/0:3          unassigned      YES unset  down                  down   
Serial0/1/0:4          unassigned      YES unset  down                  down   
Serial0/1/0:5          unassigned      YES unset  down                  down   
Serial0/1/0:6          unassigned      YES unset  down                  down   
Serial0/1/0:7          unassigned      YES unset  down                  down   
Serial0/1/0:8          unassigned      YES unset  down                  down   
Serial0/1/0:9          unassigned      YES unset  down                  down   
Serial0/1/0:10         unassigned      YES unset  down                  down   
Serial0/1/0:11         unassigned      YES unset  down                  down   
Serial0/1/0:12         unassigned      YES unset  down                  down   
Serial0/1/0:13         unassigned      YES unset  down                  down   
Serial0/1/0:14         unassigned      YES unset  down                  down   
Serial0/1/0:15         unassigned      YES unset  down                  down   
Serial0/1/0:16         unassigned      YES unset  down                  down   
Serial0/1/0:17         unassigned      YES unset  down                  down   
Serial0/1/0:18         unassigned      YES unset  down                  down   
Serial0/1/0:19         unassigned      YES unset  down                  down   
Serial0/1/0:20         unassigned      YES unset  down                  down   
Serial0/1/0:21         unassigned      YES unset  down                  down   
Serial0/1/0:22         unassigned      YES unset  up                    down   
Serial0/1/0:23         unassigned      YES unset  up                    up     
GigabitEthernet0/2/0   unassigned      YES NVRAM  administratively down down   
Service-Engine0/4/0    unassigned      YES unset  up                    up     
GigabitEthernet0       unassigned      YES NVRAM  administratively down down   
Loopback0              <removed>    YES NVRAM  up                    up     
Vlan1                  unassigned      YES NVRAM  administratively down down   
<removed>#

<removed>#sh inv
NAME: "Chassis", DESCR: "Cisco ISR4351 Chassis"
PID: ISR4351/K9        , VID: V02, SN: FLM1953W0KZ

NAME: "Power Supply Module 0", DESCR: "450W AC Power Supply for Cisco ISR4450, ISR4350"
PID: PWR-4450-AC       , VID: V01, SN: DCA1841X12J

NAME: "Fan Tray", DESCR: "Cisco ISR4450, ISR4350 Fan Assembly"
PID: ACS-4450-FANASSY  , VID:    , SN:           

NAME: "module 0", DESCR: "Cisco ISR4351 Built-In NIM controller"
PID: ISR4351/K9        , VID:    , SN:           

NAME: "NIM subslot 0/1", DESCR: "NIM-1MFT-T1/E1 - T1/E1 Serial Module"
PID: NIM-1MFT-T1/E1    , VID: V03, SN: FOC19374VAM

NAME: "subslot 0/1 db module 0", DESCR: "PVDM4-64 Voice DSP Module"
PID: PVDM4-64          , VID: V02, SN: FOC19441JTF

NAME: "NIM subslot 0/2", DESCR: "NIM-1GE-CU-SFP"
PID: NIM-1GE-CU-SFP    , VID: V01, SN: FOC195077N9

NAME: "PVDM subslot 0/4", DESCR: "PVDM4-64 Voice DSP Module"
PID: PVDM4-64          , VID: V02, SN: FOC19468DN1

NAME: "NIM subslot 0/5", DESCR: "ISR SSD Module"
PID: ISR-SSD           , VID: V01, SN: JAB092709EL

NAME: "subslot 0/5 disk0", DESCR: "harddisk"
PID: UBA2RZC200HCE1-FTC-SWD                  , VID: 5.2.4   , SN: 11001472990        

NAME: "NIM subslot 0/0", DESCR: "Front Panel 3 ports Gigabitethernet Module"
PID: ISR4351-3x1GE     , VID: V01, SN: JAB092709EL

NAME: "module 1", DESCR: "Cisco ISR4351 Built-In SM controller"
PID: ISR4351/K9        , VID:    , SN:           

NAME: "module 2", DESCR: "Cisco ISR4351 Built-In SM controller"
PID: ISR4351/K9        , VID:    , SN:           

NAME: "module R0", DESCR: "Cisco ISR4351 Route Processor"
PID: ISR4351/K9        , VID: V02, SN: FDO19480QAF

NAME: "module F0", DESCR: "Cisco ISR4351 Forwarding Processor"
PID: ISR4351/K9        , VID:    , SN:           
         

2 Replies 2

Richard Bradfield
Frequent Contributor
Frequent Contributor

Wouldn't the config be something like, this is from a 3945 so might be some differences

interface SM1/0
 ip address 172.17.224.254 255.255.255.248
 ip wccp redirect exclude in
 service-module ip address 172.17.224.251 255.255.255.248
 !Application: Restarted at Sat Jul  4 01:39:23 2015
 service-module ip default-gateway 172.17.224.254
!

HTH

Richard

Hello Richard,  That is what I thought going into this.  However not seems to be the case.


I did find this ...  and seems to be the way to setup the "Built-IN" WAAS.

http://www.cisco.com/c/en/us/td/docs/routers/access/4400/appnav/isr/isr_appnav/isr_quick_start.html

And now I have a bunch of stuff auto configured on the router that I've never seen before and don't know what its doing..... yet.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: