Hi All,Hopefully an easy question (and the right forum for it to be posted in), but I can't seem to find an answer either way in any documentation.Does the 1000v support wake on LAN?I'd like to propose the use of distributed power management (DPM) so...
Hi,sadly our N5-K's ( 5548Up, NX-OS 5.0.(3)N2.2 ) show the following issue with ntp. I asked my colleagues about the status of the ntp serverand the box seems to be fine (windows 2003 server).May 12 23:01:28 myn5k ntpd[4719]: ntp:time reset +0.2196...
Customer running Nexus 7000 6.03a. Core and Distribution VDCs. With the static RP configuration shown below,a source in VLAN 300 attached to a L2 Catalyst 6500, and a receiver on eth 1/14 on the core, multicast trafficin groups 234.5.6.7-234.5.6.11...
HiIf I have two COS values within the same queue on a 5500 port can I set drop priority for them ? I am looking at setting in contract and out of contract data rates for some VMs, setting the COS value dependant on this and then getting the 5K to be ...
First time using GLC-T's in a FEX 2232PP off of 5548 running 5.0(3)N1(1b). Was getting "sfpInvalid" on show int status. Nice engineer explained I had to remove the GLC-T's, configure the interface E101/1/1 to speed 1000 in order for the 5548/FEX to...
Anyone know how many ports per ASIC on a 2232 FEX ? We have lost connection to some servers and they are on four consecurive ports (ports 5-8) which smells of an ASIC dying. ThanksPat
Hi.I have a pretty basic design with FCoE running on a Nexus 5548 with NPV (true FC to a Brocade fabric) and Nexus 4000.Everything works fine until we have an ESX trying to reach a datastore shared by another ESX. Once the second ESX is coming, here ...
HiI have a requirment to do QoS for a DC that includes some VoIP as well FCoE with CNAs in the servers. I want to use COS 3 for the VoIP signalling and drop it in the same input and output quues to the servers as FCoE. so we haveclass-map type qos cl...
HelloI have some doubts about VM-FEX, I can only take advantage of this solution with Cisco UCS servers, right? If I have servers from other vendors, the solution is the Cisco Nexus 1000V, right? I need a solution to have more control in a new VMware...
Setup as shown in the attached. S1-S4 are Fabric path spine switches. Will it work ? or I need to configure both vlan 10 and vlan 20 in "mode fabricpath" on all S1 to S4 even though only vlan 10 is required in S1-S2 and vlan 20 required in S3-S4.
Hi,On a Nexus 1010 you have a domain. The configuration line is svs-domain. When you want to see the domain info you have to do a show svs domain. What's the meaning of those three letters SVS ? I have search a lot on internet and on cisco site. ...
Hello,We will be deploying a new Cisco Nexus 5K environment with 2248 FEX's.The firewall in the environment (non-Cisco), only supports static Port-channels - i.e "ON" configuration and not LACP.For redundancy we will be patching it into the environme...
Well our organization is planning to implement security in Datacenter for Server Farm. Therefore we are purchasing ASA 5585-X series devices. I need your suggestion that how we can implement firewall b/w Core Switch and Server Farm switch According t...
Hi,I am facing problem on Cisco Nexsus 7K. Traffic not flowing on port eth 3/47. Physical link and line protocol is also up.Then I connected to laptop by providing static IP and able to ping another end. But not working on Nexus Eth 3/47.I also t...
