We have standalone rackmounted dell servers and we want to use the load balancing Route based on Original port id. In order to accomplish the same we need to use LACP using vDS with Nexus9000 with vPC. Wanted to know whether this is supported Nexus...
Forum Posts
I have been thinking up an interesting scenario in my head, and I'm convinced the answer is a simple one that I'm overlooking. However, I've been at it for a while and decided to post the concept here and get some eyes on it.Let's say your topology i...
Dear All, The following URL is about the simplex configuration on IOS. https://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfip.html#wp1002334 But I cannot find any simplex configuration on Nexus, might anyone can advise...
Hi we want to connect some HPE Server to a Catalyst 3850-24XS-S We want to use for this DAC Cables like SFP-H10GB-ACU10M= and SFP-H10GB-ACU7M=. Does anybody know if this cables where support in GEN8 & GEN9 HPE Server NICs (like 560SFP+ & 562SFP+)...
Resolved! HP DAC Copper Cable with Cisco 4900M
We have HP C7000/VC-Flex 10 Module that I would like to connect to our Netapps NFS datastore. The Cisco switch that I will be using between HP Flex-10 and Netapps is Cisco 4900M. I have a HP cable AP784A direct attach copper SFP+ to SFP+. Whic...
Dear All, We are facing an issue in CCMP 11.0 configuration where the Provisioning Services cannot be started in services.msc. Below is a part of the logs for information. 2016-03-03 12:31:41,383 FATAL [1976] Runtime.ProvisioningController ...
Resolved! Server Conversion To 10 Gig uplinks
Greetings, I have been asked to research what would be needed to provide our servers with 10 Gig interfaces at our data center. I am not an architect and need some help deciding on what to use. Along with my own research I thought it best to inquire ...
I have 3 CSR's setup and working. Trying to get netflow to work. One works just fine but the other two aren't. Same configuration across the board, destination IP, source interface etc. The two that don't work look like they are pulling a source ...
Hi,I have 4 N7Ks (2 in each site A and B) which have OTV VDC. There are 2 WAN FO links between each pair of N7Ks like this:[OTV-A-1]-----[N7K-A-1]-----L3-----[N7K-B-1]-----[OTV-B-1] | | ...
Hello my friends I need support or help of you, i have a next case: I will go to implement OTV Tecnology with two Sites,i will use two Routers ASR,between them there are two link ISP 1 and ISP 2, and i need to do a redundancy, i sow in another do...
Hi all can I get some explanation I don't have much knowledge regarding to the below problem so I hope someone can help me with that our customer needs the DMZ server reachable from the Internet. The IIS is already installed and configured. O...
Hello, We have setup two N3K (Nexus 3172T) forming a vPC domain. The system administrators are trying to configure a cluster with 3 nodes, that runs multicast. We cluster is not able to form. I have tried to disable igmp snooping for the specific vla...
Unable to create virtual drive on UCSC-SAS-M5 (MRAID) All the button are invisible to create/ modify virtual / pyhsical drives
Hello, I have 4 Nexus 3548 Switches for Storage and Server Networking and I have done small design configuration for vPC. Can anyone pls correct my config. and give any suggestions to improve the design and Config.? File attached. Thanks!
Hello. Routers R1 and R3 are in the same AS. They are running OSPF between physical interfaces and iBGP over loopbacks on top of OSPF. R1 receives all of the routes from KCOM and has them in its routing table. R1 advertises these routes to R3 via iB...
