08-02-2011 01:43 AM
FEX 2Ks are connected to Nexus 5Ks , I am trying to add one port on the 2K to vlan 40 , vlan 40 already existing and there are active ports alredy on vlan 40. The port goes in to inactive mode soon as i add them to vlan 40. In vlan 1 the port is showing up. the message i get in console is below,
Can anyone help me out with this ?
LAS.DAF.02# sh int eth 102/1/15
Ethernet102/1/15 is down (inactive)
Hardware: 1000 Ethernet, address: 5475.d075.8250 (bia 5475.d075.8250)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, 1000 Mb/s
Beacon is turned off
Input flow-control is off, output flow-control is on
Switchport monitor is off
EtherType is 0x8100
Last link flapped 00:20:32
Last clearing of "show interface" counters never
30 seconds input rate 0 bits/sec, 0 bytes/sec, 0 packets/sec
30 seconds output rate 64 bits/sec, 8 bytes/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 80 bps, 0 pps; output rate 80 bps, 0 pps
RX
0 unicast packets 2 multicast packets 72 broadcast packets
74 input packets 15311 bytes
0 jumbo packets 0 storm suppression packets
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
0 unicast packets 93 multicast packets 0 broadcast packets
93 output packets 15786 bytes
0 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble
0 Tx pause
1 interface resets
LAS.DAF.02(config)# int eth 102/1/15
LAS.DAF.02(config-if)# switchport ACCess VLan 40
LAS.DAF.02(config-if)# 2011 Aug 2 11:19:41 LAS.DAF.02 %ETHPORT-5-IF_DOWN_CFG_CHANGE: Interface Ethernet102/1/15 is down(Config change)
2011 Aug 2 11:19:42 LAS.DAF.02 %ETHPORT-5-SPEED: Interface Ethernet102/1/15, operational speed changed to 1 Gbps
2011 Aug 2 11:19:42 LAS.DAF.02 %ETHPORT-5-IF_DUPLEX: Interface Ethernet102/1/15, operational duplex mode changed to Full
2011 Aug 2 11:19:42 LAS.DAF.02 %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet102/1/15, operational Receive Flow Control state changed to off
2011 Aug 2 11:19:42 LAS.DAF.02 %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet102/1/15, operational Transmit Flow Control state changed to on
2011 Aug 2 11:19:43 LAS.DAF.02 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 40 on Interface Ethernet102/1/15 are being suspended. (Reason: Vlan is not configured on remote vPC interface)
LAS.DAF.02# sh fex 102
FEX: 102 Description: FEX0102 state: Online
FEX version: 5.0(2)N1(1) [Switch version: 5.0(2)N1(1)]
Extender Model: N2K-C2148T-1GE, Extender Serial: JAF1408ANNQ
Part No: 73-12009-06
pinning-mode: static Max-links: 1
Fabric port for control traffic: Eth1/16
Fabric interface state:
Po102 - Interface Up. State: Active
Eth1/15 - Interface Up. State: Active
Eth1/16 - Interface Up. State: Active
LAS.DAF.02#
============================================
LAS.DAF.02# sh fex 102
FEX: 102 Description: FEX0102 state: Online
FEX version: 5.0(2)N1(1) [Switch version: 5.0(2)N1(1)]
Extender Model: N2K-C2148T-1GE, Extender Serial: JAF1408ANNQ
Part No: 73-12009-06
pinning-mode: static Max-links: 1
Fabric port for control traffic: Eth1/16
Fabric interface state:
Po102 - Interface Up. State: Active
Eth1/15 - Interface Up. State: Active
Eth1/16 - Interface Up. State: Active
LAS.DAF.02#
==============================================
LAS.DAF.02# sh vpc consistency-parameters global
Legend:
Type 1 : vPC will be suspended in case of mismatch
Name Type Local Value Peer Value
------------- ---- ---------------------- -----------------------
QoS 2 ([], [3], [], [], [], ([], [3], [], [], [],
[]) [])
Network QoS (MTU) 2 (1538, 2240, 0, 0, 0, (1538, 2240, 0, 0, 0,
0) 0)
Network Qos (Pause) 2 (F, T, F, F, F, F) (F, T, F, F, F, F)
Input Queuing (Bandwidth) 2 (50, 50, 0, 0, 0, 0) (50, 50, 0, 0, 0, 0)
Input Queuing (Absolute 2 (F, F, F, F, F, F) (F, F, F, F, F, F)
Priority)
Output Queuing (Bandwidth) 2 (50, 50, 0, 0, 0, 0) (50, 50, 0, 0, 0, 0)
Output Queuing (Absolute 2 (F, F, F, F, F, F) (F, F, F, F, F, F)
Priority)
STP Mode 1 Rapid-PVST Rapid-PVST
STP Disabled 1 None None
STP MST Region Name 1 "" ""
STP MST Region Revision 1 0 0
STP MST Region Instance to 1
VLAN Mapping
STP Loopguard 1 Disabled Disabled
STP Bridge Assurance 1 Enabled Enabled
STP Port Type, Edge 1 Normal, Disabled, Normal, Disabled,
BPDUFilter, Edge BPDUGuard Enabled Enabled
STP MST Simulate PVST 1 Enabled Enabled
Allowed VLANs - 1-2,4-5,8-10,40,50,80- 1-2,4-5,8-10,40,50,80-
81,90,100,102,105-110, 81,90,100,102,105-110,
119-123,202-203,220,24 119-123,202-203,220,24
8,252,256,258,299,330- 8,252,256,258,299,330-
331,400,800-802,900-90 331,400,800-802,900-90
5,919,2111,3001-3002,3 5,919,2111,3001-3002,3
005,3007 005,3007
Local suspended VLANs - - -
LAS.DAF.02#
Solved! Go to Solution.
08-02-2011 06:09 AM
Is the FEXs vPC back to both N5Ks? If yes, you need to put the same configuration on the same port, 102/1/15, on your second N5K to activate the port.
HTH,
jerry
08-02-2011 06:09 AM
Is the FEXs vPC back to both N5Ks? If yes, you need to put the same configuration on the same port, 102/1/15, on your second N5K to activate the port.
HTH,
jerry
08-03-2011 12:51 PM
Incase you are using VPC use below config on both N5Ks
#int eth 102/1/15
#Channel-group 123
!
#int port channel 123
#sw acess vlan 40
#vpc 123
08-03-2011 11:15 PM
Wow that was good.. It worked, would like to appreciate your quick reply. I heard in next verions this will be added as a feature.
08-04-2011 07:55 AM
The feature you want to use is called config-sync. It is available on NXOS 5.x on the N5K.
Regards,
jerry
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide