Hi all, What are the disadvantages to use the same Fusion device to be connected as a L2Handoff in the tradional network, in addition to having a single point of failure. Currently the fusion device is the GW for all the traditional vlans/segments so...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
GUIで以下のように遷移するとDHCPサーバの設定箇所が存在しますが、最大いくつまでDHCPサーバを設定可能でしょうか？ ※最低限、4つ設定可能どうか教えていただきたいです。 GUI：設計 > ネットワーク設定 > ネットワーク また、各IPアドレスプールでDHCPサーバの指定が可能だと思いますが、 最大いくつまで指定可能でしょうか？ ※最低限、4つ指定することが可能かどうか教えていただきたいです。 GUI：設計 > ネットワーク設定 > IPアドレスプール > 指定の階層を選択 4つ指...
Resolved! lisp pubsub diagnosis & t/s
teamplease share any relevant source which would include diagnosis of the dynamic border from the edge node perspective (i.e. identify preferred BN for L2 or L3 VN, identify tunnel carrying external to fabric traffic etc) ....thanks
Hi Guys,I'm looking at the Wireless options available for what will be a new FAIB site. DNAC running 2.3.3.7. The main consideration for us is that the BW is limited at sites so don't want to backhaul data traffic to a Central WLCWith the above consi...
Resolved! Access Point in Extended Node
If I have the following... 9300 acting as BN CN EN with a 3560 which I know can only be an extended node. The 9300 will have the EWC feature with Access Points split across the FEN and EN.I guess main unknown for me is, can a FEN allow for APs to be ...
Resolved! Cisco DNAC lab
I would like to setup a DNAC cluster lab for testing and learning. Is it possible to run the DNAC nodes on less then the VMware recommended system requirements?
Hello, I have implemented SDA in two sites with Fabric in a Box of two switches in a stack in each remote site. Everything is working fine without any problem. But now in one of the sites I have to add a stack of two more switches placed in another f...
Hi,Can you please tell me about all specifications of fusion router and also please clarify that this fusion router is a non poe device?
Hi I have two Border nodes Anyware and two fusion routers i configure EBGP bentween two borders (Anywhere) and two fusion i configure iBGP between the two border (Anywhere) B1-->Fusion1 : EBGP B2-->Fusion2 : EBGP B1-->B2 : iBGP when i loss the con...
According to the SDA design guide:Reduce subnets and simplify DHCP management—In the overlay, IP subnets can be stretched across the fabric without flooding issues that can happen on large Layer 2 networks. Use fewer subnets and DHCP scopes for simp...
Resolved! L2Flooding setup
Hello, When enabling L2Flooding, Underlay ASM must be configured either via LAN Automation or manually. Whatever the method used, MSDP and a Loopback60000 used as Anycast-RP should be configured on redundant Border nodes. This is documented in variou...
When adding a IP pool to a VN i want to give the VLAN a name. When i do this with the API it is not accepted and the name is auto-generated as if i do not give an name to the VLAN.The schema defenition of the api gives the required vlanName key which...
I've been searching to see if these devices have a monitoring API if they're not managed by DNA Center. Anyone know? Thanks https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9100ax-access-points/datasheet-c78-741988.html
Resolved! Loopback Interface Registration in LISP
Loopback registration in LISPHi All,I have fabric campus configured with only problem policy enforcement in inter-VN traffic. This is not working because traffic goes out of VXLAN and SGTs are lost. I want to configure my Edge switches so that they w...
Resolved! Layer 2 Border node ethernet map-cache
Hi!We have deployed a stacked 9500 as our layer 2 border node, configured with lan-automation and have an issue with migrating wired clients.We have a solution where clients authenticate with MAB over ISE and can migrate their wired connection to oth...
