Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
5031
Views
5
Helpful
9
Replies

Cisco SG200-50 GigaBit Smart Switch - can't upgrade FW

Go to solution
TorbenVejle
Level 1
Level 1

‎08-22-2014 11:46 PM

Hi,

I have tryed to upgrade the FW but get this message :

7339520
Copy failed
Copy: SW code file is over sized

 

I tryed to upgrade to Release 1.4.0.88 from release 1.3.7.18

 

The boot loader is version 1.0.0.1

Hope som one can help me to upgrade the FW.

Br. Torben Grosen

 

2 people had this problem
Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
Ismael Arroyo
Level 1
Level 1

‎08-25-2014 10:15 AM

,

 

My name is Ismael. Iam with the Small Business Support Center. From my understanding you have tried firmware upgrade and its not uploading. I like to suggest to upgrade the bootcode first before attempting the firmware. Bootcode can be found on the same zip folder as the firmware. I have tried the same in my lab with SG300 with an initial bootcode and then i upgraded it to 1.3.5.06  allowing for the firmware to upload.  So give it a try and let me know how it turns out.

View solution in original post

9 Replies 9

Go to solution
TorbenVejle
Level 1
Level 1

‎08-25-2014 08:32 AM

Hi Iarroyo,

Thanks for the mail. How do I upgrade the bootloader ?

Br. Torben Grosen

 

0 Helpful

Go to solution
TorbenVejle
Level 1
Level 1

‎08-25-2014 10:14 AM

Hi Iarroyo,

Thanks for the mail. How do I upgrade the bootloader ?

Br. Torben Grosen

0 Helpful

Go to solution
Ismael Arroyo
Level 1
Level 1

‎08-25-2014 10:15 AM

,

 

My name is Ismael. Iam with the Small Business Support Center. From my understanding you have tried firmware upgrade and its not uploading. I like to suggest to upgrade the bootcode first before attempting the firmware. Bootcode can be found on the same zip folder as the firmware. I have tried the same in my lab with SG300 with an initial bootcode and then i upgraded it to 1.3.5.06  allowing for the firmware to upload.  So give it a try and let me know how it turns out.

Go to solution
TorbenVejle
Level 1
Level 1
In response to Ismael Arroyo

‎08-25-2014 10:15 AM

Hi Iarroyo,

Thanks for the mail. How do I upgrade the bootloader ?

Br. Torben Grosen

0 Helpful

Go to solution
TorbenVejle
Level 1
Level 1
In response to Ismael Arroyo

‎08-30-2014 12:38 AM

I have now upgrade fw and boot loader using a ftp server.

Thanks :-)

0 Helpful

Go to solution
ahming000
Level 1
Level 1
In response to Ismael Arroyo

‎10-01-2014 05:28 AM

Hi Iarroyo,

  I am facing the same problem now.  Could you send the bootloader to me?  Thanks!

Leung

0 Helpful

Go to solution
Ismael Arroyo
Level 1
Level 1
In response to ahming000

‎10-01-2014 11:25 AM

ahming000,

 

If your model switch is the sg200, higher than 8 ports the firmware 1.4.0.88 would have the bootcode. Its the file named sx200_boot-13506.rfb.  This firmware can be found under Cisco.com, downloads. This same file would have to be uploaded via a TFTP server only.

0 Helpful

Go to solution
bchathurasr
Level 1
Level 1
In response to Ismael Arroyo

‎05-08-2015 08:09 AM

Hi,

I'am using SG200-50P 50-Port Gigabit PoE Smart Switch. I tried to upgrade the firmware as mentioned above. Upload the boot code first and then again try to upload the firmware upgrade. But it still keep giving the error "SW code file is over sized".

0 Helpful

Go to solution
ekontos
Level 1
Level 1
In response to Ismael Arroyo

‎06-23-2015 03:11 PM

How do you upgrade the bootloader?  Can it be done via http or ftp?  If so any directions would be great

0 Helpful
Customers Also Viewed These Support Documents