cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2066
Views
0
Helpful
3
Replies

SFP support Cisco 350 and 350X series MGBLX1

Hello,

Does Cisco 350 series model SF350-24MP and SF352-08MP-K9 and

350X series model  SG350XG-24F support    SFP MGBLX1

1 Accepted Solution

Accepted Solutions

it should work fine , it doesn't specify it in the doc but that SFP is part of same data sheet ,usually there always backward compatible the SFP+ ports

https://www.cisco.com/c/en/us/products/collateral/interfaces-modules/small-business-network-accessories/datasheet-c78-741408.html

Table 1. MGE SFP transceiver modules



Model

Description


MGBLH1

1000BASE-LH SFP transceiver for single-mode fiber, 1310 nm wavelength, supports up to 40 km


MGBLX1

1000BASE-LX SFP transceiver for single-mode fiber, 1310 nm wavelength, supports up to 10 km


MGBSX1

1000BASE-SX SFP transceiver for multimode fiber, 850 nm wavelength, supports up to 500 m


MGBT1

1000BASE-T SFP transceiver for Category 5 copper wire, supports up to 100 m

If you spec the one that works in sfop+ and the one that isn't listed , there near identical
https://www.cablerack.com/fiber-transceivers/cisco-compatible-transceivers/mgblx1.html
https://www.cablerack.com/mgblh1.html

View solution in original post

3 Replies 3

Mark Malone
VIP Alumni
VIP Alumni
Hi
The guide says yes they are supported , page 12

FP ports are compatible with Cisco modules MGBT1, MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1, and MFEBX1, as well as other brands of modules.

https://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/350_/2_3/quick_start/guide/en-US/Cisco350-QSG-en-US.pdf

Thank you Mark,

 

I asked question because I found this

https://www.cisco.com/c/en/us/products/collateral/switches/small-business-smart-switches/data-sheet-c78-737359.html

 

Supported SFP modules

SKU

Media

Speed

Maximum Distance

MGBSX1

Multimode fiber

1000 Mbps

350 m

MGBLH1

Single-mode fiber

1000 Mbps

40 km

MGBT1

UTP cat 5

1000 Mbps

100 m

 

and also for 350X

 

https://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/350xseries/2_4/admin_guide/english/AG_Tesla_350_550.pdf

 

 

page 29

 

The SFP+ ports are compatible with the following Cisco SFP 1G optical modules MGBSX1, MGBLH1, MGBT1, as well as other brands.

 

Can you confirm that SFP+ is compatibile with MGBLX1.

it should work fine , it doesn't specify it in the doc but that SFP is part of same data sheet ,usually there always backward compatible the SFP+ ports

https://www.cisco.com/c/en/us/products/collateral/interfaces-modules/small-business-network-accessories/datasheet-c78-741408.html

Table 1. MGE SFP transceiver modules



Model

Description


MGBLH1

1000BASE-LH SFP transceiver for single-mode fiber, 1310 nm wavelength, supports up to 40 km


MGBLX1

1000BASE-LX SFP transceiver for single-mode fiber, 1310 nm wavelength, supports up to 10 km


MGBSX1

1000BASE-SX SFP transceiver for multimode fiber, 850 nm wavelength, supports up to 500 m


MGBT1

1000BASE-T SFP transceiver for Category 5 copper wire, supports up to 100 m

If you spec the one that works in sfop+ and the one that isn't listed , there near identical
https://www.cablerack.com/fiber-transceivers/cisco-compatible-transceivers/mgblx1.html
https://www.cablerack.com/mgblh1.html