We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Resolved! SRW2024P Firmware File Search
Greetings all, I am hoping that a kind soul can help me with an older switch, the SRW2024P.The firmware download links are non-functional here: https://software.cisco.com/download/home/282414075/type/282463183/release/1.2.9 I am hoping to find the fi...
I'm trying to set up multiple static routes to an address in SG550XG, but load balancing can't be achieved.ip route 1.2.3.4 255.255.255.255 10.1.1.2 ip route 1.2.3.4 255.255.255.255 10.1.1.3#sh ip route static Maximum Parallel Paths: 1 (1 after reset...
Hello!try to ping 192.168.1.254 from 192.168.1.10 netmask 255.255.255.0,get Destination Host Unreachable at all.I waited 10 minutes so the switch completely booted, but no luck.Systen LED blinking so It should use default IP, and I reset the switch ....
HelloI've several crashes on my SG350XG-24F in Stack... What's the matter? %STCK SYSL-A-UNITMSG: UNIT ID 1,Msg:%SYSLOG-F-OSFATAL: caught segmentation fault exception at address 0x1daca10 signal-num = 11 (SIGSEGV) signal-code = 2 (SEGV_ACCERR) reg[00]...
Resolved! stacking SG550X-24 & SG500-28P
Hi, Is there a way to stack SG500-28P & SG550X-24 ? It looks like on an SG550X-24 switch I can choose which ports to use for stacking 10G-FiberOptics or 10G-ComboC /10G-ComboF, however on the SG500-28P stacking ports are hard set to 1G/5G ports. An...
I want to enable SPAN port on the SG300-288PP switch, However, when I tied to enable SPAN, I get the following error message but I don't have Port Security configure neither the source interface (Gi4) nor the destination interface (GI24). Is this a b...
I need a replacement power supply for a SG200-08P switch. The power supply is the one that has the 4 pins on the barrel connector. I found a similar post from 3 years ago with the same problem, but the contact email that was given is no longer valid....
Resolved! Switch no administrable
Buenos días!El día de hoy me tope con una problema en el trabajo, tienen un switch SG102-24 no administrable donde tiene conectadas varias computadoras de un área.No tienen identificados los puertos y necesito saber a que computadora corresponde cada...
Hello there, Is there anyone who can enable command authorization with tacacs+ server in Small Business Switch SG500 with the latest OS (1.4.7.5) ? The TACACS+ server is running fine with authentication/authorization for Catalyst 3850. But the this...
Hey, I'm trying to connect to my RasPi SSH via Internet.This is the Setup: SSH Internet -- > Fritzbox 192.168.178.1 --> Switch 192.168.178.2 Gi10 VLAN1 --> XXX --> RasPi 172.16.1.1 VLAN1I setup my Router (Fritzbox) with Portforwarding. The SG350 is r...
We got a Fan failure on the device.%Environment-A-FAN-STAT-CHNG: FAN# 2 status changed - not operational. Firmware version 1.4.9.4 How can we get this device replaced / fixed?
Hi everybody, I need to connect a SG350X Switch as a backup switch of a SG550X switch, and I want to know if it is possible?? for redundancy I need my switch to have a second one with the same configuration and I want to link them so that the second...
Hey,I'm trying to setup my SG350 as a DHCP Server. But I can't assign IP to some devices:My Setup:DHCP-Pool 192.168.178.100 - 192.168.178.200 (this works, Guests Network)I'm using VLAN1 with 172.16.0.0/16 My Problem:If I setup a static host for my An...
Hi my company has brought some switches from Cisco. I need to register these devices with Cisco so that I can verify warranty details and download new IOS. The vendor has provided me details like contract number,reference number.Please help me.
Hi there,I'm new to configure network switches and routers so please be thoughtful with my potentially dumb questions. Here is my problem:The SG300 switch I'm using has to two use-cases and the user shall be able to choose the use case and not be inv...
