300 series switch dhcp configuration

[pharan.b]

I am using CISCO SG300-10POE switch 

I already update firmware.

Now i have a 1.4.8.6 firmware version.

i want to configure DHCP scope and release a different ip address series  in each ports in switch.

how can i complete this task??

Thankyou  

[Seb Rupik]

hmmm, there's your problem, you only have the VLAN14 SVI configured. Try entering these commands in configuration mode again:

!
int vlan 10
  ip address 10.10.10.254 255.255.255.0
int vlan 11
  ip address 10.10.11.254 255.255.255.0
int vlan 12
  ip address 10.10.11.254 255.255.255.0
int vlan 13
  ip address 10.10.11.254 255.255.255.0
!

Confirm that the interfaces (I/F) exist by typing sh ip int

Let us know if you see any errors.

cheers,

Seb.

[pharan.b]

Done 

[Seb Rupik]

Have you set this switch to operate in router mode?

sh system mode

If state is not 'Router' then use the following command and reload:

!
set system mode router
!

This should allow you to have multiple SVIs.

cheers,

Seb.

[pharan.b]

In before switch is switch mode.

Now i change to d router mode.

Now switch is reboot.

then next.

[Seb Rupik]

Try the previous post:

!
int vlan 10
  ip address 10.10.10.254 255.255.255.0
int vlan 11
  ip address 10.10.11.254 255.255.255.0
int vlan 12
  ip address 10.10.11.254 255.255.255.0
int vlan 13
  ip address 10.10.11.254 255.255.255.0
!

Confirm that the interfaces (I/F) exist by typing sh ip int

Let us know if you see any errors.

If sh ip int, shows you VLAN SVIs 10-14, then when you connect to Gi1 you should get a lease!

cheers,

Seb.

[pharan.b]

Now It's change to router mode.

[Seb Rupik]

Have you typed in the int vlan commands from above??

[pharan.b]

Yes. I have completed this command.

and d output is!! 

And d next screenshot is connect a system on a first port on switch.

But it cannot release a dhcp 10 series?

[Seb Rupik]

the output of sh vlan, tells you that VLAN1 is configured un-tagged on all ports. You need to configure your other VLANs to be untagged on each port. This was part of the initial  config I provided last week. Just enter these commands:

!
int gi1
  switchport access vlan 10
int gi2
  switchport access vlan 11
int gi3
  switchport access vlan 12
int gi4
  switchport access vlan 13
int gi5
  switchport access vlan 14
!

cheers,

Seb.

[pharan.b]

There is an error Buddy.

If i continue or want to doing something. 

[Seb Rupik]

!
int range gi1-5
  switchport mode access
!
int gi1
  switchport access vlan 10
int gi2
  switchport access vlan 11
int gi3
  switchport access vlan 12
int gi4
  switchport access vlan 13
int gi5
  switchport access vlan 14
!

[pharan.b]

I completed this command 

But still i receive a dhcp on system ip series is 169 only??

after i complete all this configuration.

I just connect a system in switch first port.

I have receive only a 169 series ip address.

what i want to do can i receive a configure dhcp ip address on first port.

It's have been a long time. to make i complete this task.

There is any options avaliable are there.    

[Seb Rupik]

Can you provide the entire output of sh run, to see what state the configuration is in?

[pharan.b]

This is ??

[pharan.b]

Just simple.

i just do that reset switch, If u say yes.

Then we try to configure only one port like gi1 And configure a 192 series ip address on DHCP on first port.

If can we countinue that??