3560G routed port connected to E1 converter
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2013 01:09 PM - edited 03-07-2019 01:33 PM
Hi All
I have made a routed port on 3560G Switch and defined a pool 172.28.4.62 255.255.255.192 and connected to E1 converter RAD (4E1 to 4 FE) the E1 media is through Microwave on the other end same E1 converter is connected through layer 2 switch and defined a pool as of routed port configured in 3560G switch.
The port is generating lot of giants and after a while it also distrubs other routes ( Port1 to Port 16), configured with Vlan11 and port 22 as routed port.
I have checked the routed port through wireshark the maximum frame size is 1514 and configured the MTU to 1514, giants are not showing any more but after 10 to 12 hours switch gets hang. Either to shut the port or to reload the switch to get switch and other layer routes to be normal.
I have checked speed and duplex settings same as E1 converter. Full duplex. 100 Speed. Can you please guide why switch is not behaving normal. If i shutdown the routed port it is normal.
1. interface GigabitEthernet0/22
no switchport
ip address 172.28.4.62 255.255.255.192
flowcontrol receive on
end
2. #sh int g0/22
GigabitEthernet0/22 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is f025.7292.3bc3 (bia f025.7292.3bc3)
Internet address is 172.28.4.62/26
MTU 1514 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX
input flow-control is on, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 08:12:58
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 32000 bits/sec, 37 packets/sec
5 minute output rate 29000 bits/sec, 30 packets/sec
1511472 packets input, 193066909 bytes, 0 no buffer
Received 329372 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 315319 multicast, 0 pause input
0 input packets with dribble condition detected
1388683 packets output, 204952330 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
3 #sh controllers ethernet-controller g0/22
Transmit GigabitEthernet0/22 Receive
208662623 Bytes 196571703 Bytes
1395739 Unicast frames 1201317 Unicast frames
16539 Multicast frames 320932 Multicast frames
2139 Broadcast frames 14295 Broadcast frames
0 Too old frames 153120428 Unicast bytes
0 Deferred frames 42497542 Multicast bytes
0 MTU exceeded frames 952215 Broadcast bytes
0 1 collision frames 0 Alignment errors
0 2 collision frames 2 FCS errors
0 3 collision frames 0 Oversize frames
0 4 collision frames 0 Undersize frames
0 5 collision frames 0 Collision fragments
0 6 collision frames
0 7 collision frames 23168 Minimum size frames
0 8 collision frames 1386857 65 to 127 byte frames
0 9 collision frames 71215 128 to 255 byte frames
0 10 collision frames 12671 256 to 511 byte frames
0 11 collision frames 7251 512 to 1023 byte frames
0 12 collision frames 35355 1024 to 1518 byte frames
0 13 collision frames 0 Overrun frames
0 14 collision frames 0 Pause frames
0 15 collision frames
0 Excessive collisions 0 Symbol error frames
0 Late collisions 0 Invalid frames, too large
0 VLAN discard frames 29 Valid frames, too large
0 Excess defer frames 0 Invalid frames, too small
68034 64 byte frames 0 Valid frames, too small
1167217 127 byte frames
116592 255 byte frames 0 Too old frames
10709 511 byte frames 0 Valid oversize frames
4070 1023 byte frames 0 System FCS error frames
47795 1518 byte frames 0 RxPortFifoFull drop frame
0 Too large frames
0 Good (1 coll) frames
0 Good (>1 coll) frames
- Labels:
-
Other Switching

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2013 01:34 PM
Update switch software and check again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2013 06:18 PM
Thanks this is current version i am using... can you please suggest which version to upgrade....
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 28 WS-C3560G-24TS 15.0(2)SE2 C3560-IPSERVICESK9-M

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-27-2013 05:27 AM
I would try latest 12.2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-27-2013 07:53 AM
Dear the version 15.0(2)SE2 is latest was released in 10-Feb 2013 whereas version 12.2.58-SE2 was released in 27-July 2011. should i downgrade the software version.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-27-2013 08:17 AM
Just try, won't hurt.
