03-04-2013 02:46 AM - edited 03-07-2019 12:02 PM
Hello,
I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
With kind regards,
Martijn.
03-04-2013 03:06 AM
HSRP is supported in Ipbase and IP Services Lic.
Kindly check Lic is activated or not.
*** Do Rate Helpful Posts***
03-04-2013 03:09 AM
Hello,
I even activated ip services on 3850, but i still can't activate standby commands on interface vlan.
I turned on ip routing. I'm i forgetting something?
03-04-2013 03:13 AM
Can u Post Config where you are using standby command with ?
03-04-2013 03:17 AM
Well it seems HSRP isn't supported! See release notes IOS XE Version 03.02.00SE
The following features are not supported in Cisco IOS XE Release 3.2.0SE:
•Outdoor Access Points
•Mesh, Flexconnect and OEAP deployment
•Full-features Web-based User Interface (Monitoring-specific pages are supported.)
•Secure Group Access (SXP, SGT)
•Profiling and on boarding
•Wireless Guest Anchor Controller (The Catalyst 3850 switch can be configured as a foreign controller.)
•IPv6 Multicast Routing
•Resilient Ethernet Protocol
•Hot Standy Router Protocol (HSRP)
•Virtual Router Redundancy Protocol (VRRP)
•Private VLANs
•Device Sensor
•MVR (Multicast VLAN Registration)
•Secure Group Access - Security Group Tag (SGT) Secure Goup Access List (SGACL)
•Security Group Tag (SGT) Exchange Protocol (SXP)
•EnergyWise
•IPv6 routing - OSPFv3 Authentication
•Call Home
•Critical VLAN for voice devices
•IPv6 First Hop Security: IPv6 Source Guard
•DVMRP Tunneling
•Port Security on Etherchannel
•802.1x Configurable username and password for MAB
•Gov't Certs: Common Criteria & FIPS
•802.3z (CWDM)
•Link State Tracking (L2 Trunk Failover)
•Disable Per VLAN MAC Learning
•IEEE 802.1X-2010 with 802.1AE support
•IEEE 802.1AE MACsec (MKA & SAP)
•Command Switch Redundancy
•CNS Config Agent
•Dynamic Access Ports
•IPv6 Ready Logo phase II - Host
•IPv6 IKEv2 / IPSecv3
•OSPFv3 Graceful Restart (RFC 5187)
•Fallback bridging for non-IP traffic between VLANs
•Support for 16 static IPv4 routes in LAN Base
•DHCP snooping ASCII circuit ID
•Protocol Storm Protection
•802.1x NEAT
•Per VLAN Policy & Per Port Policer
•Packet Based Storm Control
•Ingress/egress Shared Queues
•Trust Boundary Configuration
•Cisco Group Management Protocol (CGMP)
•Device classifier for ASP
•IPSLA Media Operation
•Mediatrace
•Passive Monitoring
•Performance Monitor (Phase 1)
•AAA: Radius over IPv6 transport
•AAA: Tacacs over IPv6 Transport
•Auto QoS for Video endpoints
•EX SFP Support (GLC-EX-SMD)
•IPv6 Strict Host Mode Support
•IPv6 Static Route support on Lanbase images
•VACL Logging of access denied
•RFC5460 DHCPv6 Bulk Leasequery
•DHCPv6 Relay Source Configuration
•RFC 4293 IP-MIB (IPv6 only)
•RFC 4292 IP-FORWARD-MIB (IPv6 only)
•RFC4292/RFC4293 MIBs for IPv6 traffic
03-04-2013 06:00 AM
Thanks for the heads up on this one. I am disappointed with this. Cisco tells us:
"Since Cisco IOS XE contains Cisco IOS within itself as IOSd, all features created within IOS will also appear in IOS XE and vice versa. Only new integrated services and functionality created outside of IOSd will not be shared with a Cisco IOS release. However, these integrated services may be introduced on a Cisco IOS platform through the use of Integrated Services daughter cards which will be available on a platform by platform basis."
And we get that huge list of unsupported features instead. I did not see GLBP listed in there have you tried configuring that?
03-13-2013 11:47 AM
Greg and Martijn,
You would think, they would be available day1 right
According to the ask the expert Q&A, HSRP, VRRP is coming sometimes in 2013:
Have a look:
https://supportforums.cisco.com/thread/2204255?tstart=0
HTH
Reza
07-22-2014 07:11 AM
Hi...
I want to configure HSRP on cisco 3850 Switch.
can you please help me..
This is the Software version installed on it...
WS-C3850-24P 03.02.03.SE cat3k_caa-universalk9 INSTALL
SW1-OPT#sho license right-to-use summary
License Name Type Count Period left
-----------------------------------------------
ipservices permanent N/A Lifetime
apcount base 0 Lifetime
apcount adder 0 Lifetime
--------------------------------------------
License Level In Use: ipservices
License Level on Reboot: ipservices
Evaluation AP-Count: Disabled
Total AP Count Licenses: 0
AP Count Licenses In-use: 0
AP Count Licenses Remaining: 0
07-22-2014 12:00 PM
You need 3.3 for HSRP.
03-13-2013 08:52 AM
Hi, Martijn, can you verify any other protocol than provide high availability like hsrp or vrrp?
Regards
Franks
08-05-2013 07:03 PM
Coming in 3.3.0 (estimated Oct/Nov)
HSRPv2, VRRPv2
07-23-2014 03:23 PM
Thanks a lot Luke..
I have upgraded the Software version to 3.3.3 and It worked...
09-29-2020 07:14 AM
hi can i get ios version 3.3.3
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide