cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1486
Views
5
Helpful
8
Replies

3850 stack dropping packets

awojtowicz
Level 2
Level 2

i have a 3850 stack of 2 switches in my mdf.  i have another switch in my idf connected by fiber.  everything has been good for years.  i just added another 3850 switch into my stack in my mdf.  now i cant access by idf switch at all.  cant ping or putty it.  but it shows in show cdp neighbor.  i have some FortiAP's on switch 1 in my mdf stack.  i keep losing them every so often.  i'll run a constant ping to something else behind the network and i lose 6 packets every time when this happens.  i drop all packets into this network whenever this 6 packet drop happens.  i even took that switch i added out of the stack and it doesnt matter, the same problem.  It was a bare switch.  same OS.  ive done this many times in my network but never had this happen before.

1 Accepted Solution

Accepted Solutions

awojtowicz
Level 2
Level 2

found issue.  it was something over looked.  it had a mgmt vlan setup but when adding the switch it sorta removed it.  settings were there but not working.  just added back the vlan resolved all issues.

View solution in original post

8 Replies 8

Mark Elsen
Hall of Fame
Hall of Fame

 

   - @awojtowicz                Check logs on the  stack when manipulations are done, such as adding or deleting
                                          a stack member , do the same on other switches involved in the issue; if any
                                          Use and or define a common syslog server which is a better solution for collecting logs

 M.



-- ' Listen to the wind, it talks  
          Listen to the silence, it speaks
             Listen to your heart, it knows
Ganado Mucho (1809 to 1893 ) Navajo Indian

DFWTechGuy
Level 6
Level 6

Since the issue started after adding the new 3850, I’d check the stack and uplink status first, even though removing the switch didn’t fix it.

You can check show switch, show switch stack-ports, and show interfaces counters errors to see if there are any stack-port or interface errors. I’d also check the fiber uplink to the IDF switch and compare the running configs to see if anything changed with VLANs, trunks, or spanning tree.

The fact that the IDF switch still shows up in CDP but you can’t ping or SSH into it is a useful clue.

Levi - DFWTechGuy

Leo Laohoo
Hall of Fame
Hall of Fame

Post the complete output to the following commands: 

sh platform resources 
sh platform software status control-processor brief

BOE_MDF_3850STK#sh platform resources
**State Acronym: H - Healthy, W - Warning, C - Critical
Resource Usage Max Warning Critical State
----------------------------------------------------------------------------------------------------
Control Processor 6.50% 100% 90% 95% H
DRAM 2267MB(58%) 3866MB 90% 95% H

BOE_MDF_3850STK#sh platform software status control-processor brief
Load Average
Slot Status 1-Min 5-Min 15-Min
1-RP0 Healthy 0.66 0.63 0.55
2-RP0 Healthy 0.07 0.24 0.30
3-RP0 Healthy 0.12 0.17 0.15

Memory (kB)
Slot Status Total Used (Pct) Free (Pct) Committed (Pct)
1-RP0 Healthy 3959052 2322316 (59%) 1636736 (41%) 3025316 (76%)
2-RP0 Healthy 3959052 2275060 (57%) 1683992 (43%) 2989260 (76%)
3-RP0 Healthy 3959052 1045404 (26%) 2913648 (74%) 1247032 (31%)

CPU Utilization
Slot CPU User System Nice Idle IRQ SIRQ IOwait
1-RP0 0 4.30 2.00 0.00 93.60 0.00 0.10 0.00
1 5.10 1.70 0.00 93.10 0.00 0.10 0.00
2 4.99 1.79 0.00 93.10 0.00 0.09 0.00
3 5.30 2.10 0.00 92.60 0.00 0.00 0.00
2-RP0 0 4.30 2.00 0.00 93.60 0.00 0.10 0.00
1 2.70 0.80 0.00 96.50 0.00 0.00 0.00
2 3.50 1.10 0.00 95.30 0.00 0.10 0.00
3 2.50 1.10 0.00 96.39 0.00 0.00 0.00
3-RP0 0 1.09 1.19 0.00 97.60 0.00 0.09 0.00
1 2.90 1.10 0.00 96.00 0.00 0.00 0.00
2 1.60 1.30 0.00 97.09 0.00 0.00 0.00
3 2.00 1.30 0.00 96.70 0.00 0.00 0.00

Can you check the output to the command "sh controller util".  This command is a real-time snapshot of each link utilization (upload and download).  

Anything more than 10% is not good.  

All 0's.

Memory utilization is normal. 

Real-time link utilization is normal. 

I do  not see any evidence coming from this switch that this is the source of the packet drops. 

Try this:  Plug a machine in the same switch member, put in the same VLAN as the machine dropping packets.  

Ping the machine dropping packets.  Are the packets dropping?

awojtowicz
Level 2
Level 2

found issue.  it was something over looked.  it had a mgmt vlan setup but when adding the switch it sorta removed it.  settings were there but not working.  just added back the vlan resolved all issues.