09-11-2018 08:21 AM - edited 03-08-2019 04:08 PM
We have a Cisco 4506-E chassis that has three switching modules installed and they all had an amber status. I restarted the switch which didn't resolve the issue. I re-seated each module and only one of them changed to a green status. I did a hw reset on the other two modules and they came back online but are still amber. I cleaned the side vents and used dry air. I ran the CLI analyzer and no bugs were detected any idea's would be greatly appreciated. Any assistance would be greatly appreciated, Thanks.
HS-145-4506.17#sh mod
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 6 Sup 6L-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6L-E JAE152908J8
2 48 10/100/1000BaseT POE E Series WS-X4648-RJ45V-E JAE15290FUZ
3 48 10/100/1000BaseT POE E Series WS-X4648-RJ45V-E JAE152700KZ
4 48 10/100/1000BaseT POE E Series WS-X4648-RJ45V-E JAE153007Q7
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 e8b7.488e.6f40 to e8b7.488e.6f45 3.0 12.2(44r)SG1 12.2(53)SG4 Ok
2 30e4.dbf0.db60 to 30e4.dbf0.db8f 2.0 Ok
3 30e4.dbf0.f4b0 to 30e4.dbf0.f4df 2.0 Ok
4 30e4.db23.5590 to 30e4.db23.55bf 2.0 Ok
HS-145-4506.17#sh env
warning alarm: slot 2 has exceeded the warning temperature for 0h 40m 35s
warning alarm: slot 4 has exceeded the warning temperature for 0h 39m 33s
Module Sensor Temperature Status
------+--------------------------+--------------------+------------
1 air inlet 37C (51C,65C,68C) ok
1 air outlet 45C (69C,83C,86C) ok
2 air inlet 46C (45C,60C,70C) warning
2 air outlet 48C (61C,76C,86C) ok
3 air inlet 44C (45C,60C,70C) ok
3 air outlet 46C (61C,76C,86C) ok
4 air inlet 50C (45C,60C,70C) warning
4 air outlet 48C (61C,76C,86C) ok
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C45-1300ACV AC 1300W good good good
PS2 PWR-C45-1300ACV AC 1300W good good good
Power supplies needed by system : 1
Power supplies currently available : 2
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Switch Bandwidth Utilization : 0%
Supervisor Led Color : Green
Module 1 Status Led Color : Green
Module 2 Status Led Color : Orange PoE Led Color : Green
Module 3 Status Led Color : Green PoE Led Color : Green
Module 4 Status Led Color : Orange PoE Led Color : Green
Fantray : Good
Fantray removal timeout : 30
Power consumed by Fantray : 120 Watts
09-11-2018 09:37 AM
Try putting the 2 modules with this issue in different slots.
HTH
09-11-2018 04:37 PM
04-15-2019 09:35 AM - edited 04-15-2019 09:36 AM
@Quintin.Mayo wrote:
HS-145-4506.17#sh env
warning alarm: slot 2 has exceeded the warning temperature for 0h 40m 35s
warning alarm: slot 4 has exceeded the warning temperature for 0h 39m 33s
Module Sensor Temperature Status
------+--------------------------+--------------------+------------
1 air inlet 37C (51C,65C,68C) ok
1 air outlet 45C (69C,83C,86C) ok
2 air inlet 46C (45C,60C,70C) warning
2 air outlet 48C (61C,76C,86C) ok
3 air inlet 44C (45C,60C,70C) ok
3 air outlet 46C (61C,76C,86C) ok
4 air inlet 50C (45C,60C,70C) warning
4 air outlet 48C (61C,76C,86C) ok
Maybe I'm too new and dumb, but it seems the lights are simply indicating that the Inlet temp for both 2 and 4 are over the warning limit?
Is the switch in a room with a low enough ambient temperature?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide