cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
616
Views
0
Helpful
4
Replies

6509 vss standby error

opnineopnine
Level 1
Level 1

Hello,

I just configured my vss in the 2 6509, the issue is that in the standby 6509 all the ports in the line cards go ambar. I do a no shut to all the range but still the same issue.

thanks.

4 Replies 4

Furose M
Level 3
Level 3

please post "show module switch all" and "show redundancy" output.

it looks like the standby is not in SSO mode. if standby is not in SSO mode, the linecards of its chassis wont initialize.

Hello,

"sh module"
"Mod Ports Card Type                              Model              Serial No."
"--- ----- -------------------------------------- ------------------ -----------"
"  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX                "
"  2   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX                "
"  3   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX                "
"  4   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP                  "
"  5    5  Supervisor Engine 720 10GE (Active)    VS-S720-10G                   "
"  6    5  Supervisor Engine 720 10GE (Hot)       VS-S720-10G                   "
"Mod MAC addresses                       Hw    Fw           Sw           Status"
"--- ---------------------------------- ------ ------------ ------------ -------"
"  1  0021.a04a.6670 to 0021.a04a.669f   3.0   12.2(18r)S1  12.2(33)SXH4 Ok"
"  2  0021.a04a.6610 to 0021.a04a.663f   3.0   12.2(18r)S1  12.2(33)SXH4 Ok"
"  3  0023.5ebc.d450 to 0023.5ebc.d47f   3.0   12.2(18r)S1  12.2(33)SXH4 Ok"
"  4  0024.14d7.8480 to 0024.14d7.84af   1.12  12.2(14r)S5  12.2(33)SXH4 Ok"
"  5  001e.4a7e.7a20 to 001e.4a7e.7a27   2.1   8.5(2)       12.2(33)SXH4 Ok"
"  6  001f.6cbd.0cf8 to 001f.6cbd.0cff   2.1   8.5(2)       12.2(33)SXH4 Ok"
"Mod  Sub-Module                  Model              Serial       Hw     Status "
"---- --------------------------- ------------------ ----------- ------- -------"
"  1  Distributed Forwarding Card WS-F6700-DFC3C     SAL1302G0JM  1.1    Ok"
"  2  Distributed Forwarding Card WS-F6700-DFC3C     SAL1302G0JL  1.1    Ok"
"  3  Distributed Forwarding Card WS-F6700-DFC3C     SAL1302FTK5  1.1    Ok"
"  4  Distributed Forwarding Card WS-F6700-DFC3C     SAL1302FRFY  1.1    Ok"
"  5  Policy Feature Card 3       VS-F6K-PFC3C       SAL1301FLH4  1.0    Ok"
"  5  MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1253EU19  1.0    Ok"
"  6  Policy Feature Card 3       VS-F6K-PFC3C       SAL1252EMQB  1.0    Ok"
"  6  MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1301FFTT  1.0    Ok"
"Mod  Online Diag Status "
"---- -------------------"
"  1  Pass"
"  2  Pass"
"  3  Pass"
"  4  Pass"
"  5  Pass"
"  6  Pass"

thanks.

are you sure its running in VSS mode? please provide me with the outputs i requested in 1st comment.

Hello Furose,

Sorry for the delay with my answer, the issue is that we need to do a full rollback,

This is the output I had the chance to get.

CORE01#show redundancy states
       my state = 13 -ACTIVE
     peer state = 8  -STANDBY HOT
           Mode = Duplex
           Unit = Primary
        Unit ID = 21

Redundancy Mode (Operational) = sso
Redundancy Mode (Configured)  = sso
Redundancy State              = sso
     Maintenance Mode = Disabled
 Communications = Up

   client count = 76
 client_notification_TMR = 30000 milliseconds
          keep_alive TMR = 9000 milliseconds
        keep_alive count = 1
    keep_alive threshold = 18
           RF debug mask = 0x0  
!!

The show modules I was not able to get it.

Thanks.