Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1028
Views
0
Helpful
4
Replies

871W and Radio Interface

Syed Faraz Ali
Level 1
Level 1

‎01-24-2013 04:31 AM - edited ‎03-07-2019 11:17 AM

Hi,

   I have configured Cisco 871W with Wifi and Lan ports for user access . LAN ports seems to be working fine however SSID is not being broadcasted , following is configuration of my 871W 

version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname CISCO-871-W
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
!
!
dot11 syslog
dot11 vlan-name MY-LAN vlan 2
!
dot11 ssid MY-WIRELESS
 authentication open
 guest-mode
!
ip source-route
!
!
!
ip dhcp pool LAN-CLIENTS
   network 192.168.3.0 255.255.255.0
   default-router 192.168.3.1
!
ip dhcp pool WIFI-CLIENTS
   network 192.168.4.0 255.255.255.0
   default-router 192.168.4.1
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
!
!
archive
 log config
  hidekeys
!
!
!
bridge irb
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
 description **WAN INTERFACE**
 ip address 10.0.0.1 255.255.255.0
 duplex auto
 speed auto
!
interface Dot11Radio0
 no ip address
 no ip route-cache cef
 no ip route-cache
 !
 ssid MY-WIRELESS
 !
 speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
 station-role root
!
interface Dot11Radio0.1
 encapsulation dot1Q 1 native
 no ip route-cache
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface Vlan1
 ip address 192.168.3.1 255.255.255.0
!
interface BVI1
 ip address 192.168.4.1 255.255.255.0
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
!
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
!
line con 0
 no modem enable
line aux 0
line vty 0 4
 login
!
scheduler max-task-time 5000

CISCO-871-W#show ip int br
Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       192.168.4.1     YES manual down                  down
Dot11Radio0                unassigned      YES manual reset                 down
Dot11Radio0.1              unassigned      YES unset  reset                 down
FastEthernet0              unassigned      YES unset  up                    down
FastEthernet1              unassigned      YES unset  down                  down
FastEthernet2              unassigned      YES unset  up                    down
FastEthernet3              unassigned      YES unset  up                    down
FastEthernet4              10.0.0.1        YES manual up                    up
Vlan1                      192.168.3.1     YES manual up                    down

Labels:
0 Helpful
4 Replies 4

Gregory Snipes
Level 4
Level 4

‎01-24-2013 06:14 AM

Your BVI is configured incorrectly. You should not have an IP on VLAN 1 and you should use the "bridge-group 1" command on it. As it is the dot11radio0.1 interface is not connected to anything and as such is not coming up.

0 Helpful

Gregory Snipes
Level 4
Level 4

‎01-25-2013 09:12 AM

Also if you wanted to keep your wireless clients on a different subnet then your wired clients. You could always create a second SVI, say vlan 2, and put the wired ports in that other vlan.

0 Helpful

Syed Faraz Ali
Level 1
Level 1
In response to Gregory Snipes

‎01-25-2013 09:46 PM

Now i did this configuration, but i am unable to get IP address from DHCP on LAN & WLAN, when i manually configure IP address on host's wired lan, it does not work. but when i manually configure IP address on host's wireless lan interface it works perfect. i want my hosts on LAN & WLAN should get ip address from DHCP.

hostname Cisco-871w
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
!
!
no dot11 syslog
!
dot11 ssid MY-WIRELESS
 authentication open
 guest-mode
!
ip source-route
!
!
!
ip dhcp pool MY-CLIENTS
   import all
   network 172.16.142.0 255.255.255.0
   dns-server 172.16.0.202
   default-router 172.16.142.254
!
!
ip cef
ip domain name mynet.com
ip name-server 172.16.0.202
no ipv6 cef
!
multilink bundle-name authenticated
!
!
archive
 log config
  hidekeys
!
!
!
bridge irb
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
 description " WAN INTERFACE "
 ip address 172.19.29.142 255.255.255.252
 ip tcp adjust-mss 1300
 duplex auto
 speed auto
!
interface Dot11Radio0
 ip address 172.16.142.254 255.255.255.0
 no ip route-cache cef
 no ip route-cache
 !
 ssid MY-WIRELESS
 !
 speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0
 channel 2412
 station-role root
 antenna gain 0
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface Vlan1
 no ip address
 bridge-group 1
!
interface BVI1
 no ip address
!
!
ip default-gateway 172.16.142.254
ip forward-protocol nd
!
!
control-plane
!
bridge 1 protocol ieee
!

Cisco-871w#sh ip int br
Interface                      IP-Address         OK? Method Status                Protocol
BVI1                            unassigned        YES manual up                      up
Dot11Radio0                172.16.142.254   YES manual up                      up
FastEthernet0              unassigned         YES unset  down                   down
FastEthernet1              unassigned         YES unset  up                       down
FastEthernet2              unassigned         YES unset  up                       down
FastEthernet3              unassigned         YES unset  up                       down
FastEthernet4              172.19.29.142     YES manual up                     down
Vlan1                          unassigned          YES manual up                     down

0 Helpful

Syed Faraz Ali
Level 1
Level 1
In response to Syed Faraz Ali

‎01-27-2013 11:45 PM

now i did this configuration and i am able to get ip from DHCP on both LAN & WLAN segment but with different subnet.

now i want my clients on LAN & WLAN must get ip address of same segment. 

Current configuration : 5012 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname BNC
!
boot-start-marker
boot-end-marker
!
!
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
aaa session-id common
!
resource policy
!
ip subnet-zero
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 172.16.142.1 172.16.142.10
ip dhcp excluded-address 172.16.142.254
ip dhcp excluded-address 172.16.241.1 172.16.241.10
!
ip dhcp pool b&c-department
   import all
   network 172.16.142.0 255.255.255.0
   dns-server 172.16.0.202
   default-router 172.16.142.254
!  lease 7
!
ip dhcp pool VLAN20
 import all
 network 172.16.241.0 255.255.255.0
 dns-server 172.16.0.202
 default-router 172.16.241.1
 lease 7
!
!
ip cef
ip name-server 172.16.0.202
no ipv6 cef
!
!
!
!
bridge irb
!
interface Loopback1
 ip address 172.16.200.142 255.255.255.255
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
 description " WAN LINK "
 ip address 172.19.29.142 255.255.255.252
 ip tcp adjust-mss 1300
 duplex auto
 speed auto
!
interface Dot11Radio0
no ip address
!
no encryption vlan 1 mode ciphers tkip
!
no encryption vlan 20 mode ciphers tkip
!
ssid GuestWLAN
vlan 20
authentication open
guest-mode
!
ssid InternalWLAN
vlan 1
authentication open
!
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2462
station-role root
no dot11 extension aironet
no cdp enable
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no snmp trap link-status
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio0.2
!
interface Dot11Radio0.20
description Guest wireless LAN - routed WLAN
encapsulation dot1Q 20
ip address 172.16.241.1 255.255.255.0
ip virtual-reassembly
!
interface Vlan1
description Internal Network
no ip address
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
!
interface BVI1
description Bridge to Internal Network
ip address 172.16.142.254 255.255.255.0
ip virtual-reassembly
router rip
 version 2
 network 172.16.0.0
 network 192.168.142.0
 network 172.16.241.0
 no auto-summary
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.142.20
ip route 172.19.29.0 255.255.255.0 172.19.29.141
ip http server
ip http secure-server
ip dns server
!
snmp-server community r3g10n RO
snmp-server location B&C
!
control-plane
!
bridge 1 route ip
!

0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking for a $25 gift card