cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
966
Views
0
Helpful
12
Replies

C3750-e requires ROMmon to boot

I have 3 new (used but new to me) C3750-e.

for each one, I fired it up, did a minimal config, downloaded the ios image I use in all my 3750s, gave it the following commands:

boot system switch all flash:c3750e-ipbasek9-mz.122-55.SE12.bin
write mem
reload

the first 2 switches, worked no problem. On the third switch I screwed up the boot command and instead issued the command:

system switch all flash:c3750e-ipbasek9-mz.122-55.SE12.bin

I did not get an error message on the console. But after issuing the reload command, it did not boot all the way. The console output showed only:

Using driver version 1 for media type 2
Base ethernet MAC Address: 00:24:13:c4:64:80
Xmodem file system is available.
The password-recovery mechanism is enabled.

If I then reboot into ROMmon mode, issue:

flash_init
boot flash:c3750e-ipbasek9-mz.122-55.SE12.bin

It booted up no problem. So I then attempted to fix the boot system by issuing the correct command as in the first two switches I configured. Verified this time with "show boot" and it displayed the correct image to boot. reload... same problem. it never fully boots. everytime it does slow flashing syst light, then flast flashhing Syst light, then solid light and at this point the console displays: 

Using driver version 1 for media type 2
Base ethernet MAC Address: 00:24:13:c4:64:80
Xmodem file system is available.
The password-recovery mechanism is enabled.

and nothing more no matter how long I wait. But if I then power down, press the mode light, plug inpower and hold mode light till syst light is solid, then I see on the console:

The system has been interrupted prior to initializing the
flash filesystem. The following commands will initialize
the flash filesystem, and finish loading the operating
system software:

flash_init
boot

So I do the 2 commands and it boots.

How do I fix it so it boots on its own without me having to do ROMmon?

12 Replies 12

Leo Laohoo
Hall of Fame
Hall of Fame

If it boots up in IOS, post the complete output to the command "sh boot".

sw-rok2#show flash

Directory of flash:/

2 -rwx 616 Feb 28 1993 16:01:36 -08:00 vlan.dat
3 -rwx 1936 Dec 1 2022 17:19:48 -08:00 private-config.text
4 -rwx 2072 Dec 1 2022 17:19:48 -08:00 multiple-fs
5 -rwx 14610998 Dec 1 2022 14:19:33 -08:00 c3750e-ipbasek9-mz.122-55.SE12.bin
6 -rwx 2909 Dec 1 2022 17:19:48 -08:00 config.text

57409536 bytes total (42668032 bytes free)
sw-rok2#
sw-rok2#
sw-rok2#
sw-rok2#show boot
BOOT path-list : flash:c3750e-ipbasek9-mz.122-55.SE12.bin
Config file : flash:/config.text
Private Config file : flash:/private-config.text
Enable Break : no
Manual Boot : no
HELPER path-list :
Auto upgrade : yes
Auto upgrade path :
NVRAM/Config file
buffer size: 524288
Timeout for Config
Download: 0 seconds
Config Download
via DHCP: disabled (next boot: disabled)
sw-rok2#
sw-rok2#
sw-rok2#
sw-rok2#show ver
Cisco IOS Software, C3750E Software (C3750E-IPBASEK9-M), Version 12.2(55)SE12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Thu 28-Sep-17 01:02 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000

ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750E-HBOOT-M) Version 12.2(44r)SE5, RELEASE SOFTWARE (fc3)

sw-rok2 uptime is 14 hours, 59 minutes
System returned to ROM by power-on
System restarted at 17:27:01 PST Thu Dec 1 2022
System image file is "flash:c3750e-ipbasek9-mz.122-55.SE12.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

License Level: ipbase
License Type: Permanent
Next reload license Level: ipbase

cisco WS-C3750E-24TD (PowerPC405) processor (revision F0) with 262144K bytes of memory.
Processor board ID FDO1248R0YR
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
28 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:24:13:C4:64:80
Motherboard assembly number : 73-10313-11
Motherboard serial number : FDO12480DL9
Model revision number : F0
Motherboard revision number : A0
Model number : WS-C3750E-24TD-S
Daughterboard assembly number : 800-28590-01
Daughterboard serial number : FDO1248088T
System serial number : FDO1248R0YR
Top Assembly Part Number : 800-27546-03
Top Assembly Revision Number : A0
Version ID : V02
CLEI Code Number : COMSE00ARA
Hardware Board Revision Number : 0x01


Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 30 WS-C3750E-24TD 12.2(55)SE12 C3750E-IPBASEK9-M


Configuration register is 0xF

Console into the switch and reboot.  Post the entire boot-up process.  We want to see what actually breaks.

Hi Leo

thanks for looking at this with me. Here is the entirety of what displays on the console for the full boot process from power on until I get a prompt. This includes where I give the boot command at the ROMmon prompt. If I simply boot without holding down the status button to enter ROMmon, I only get the first 4 lines of below and then it just hangs and goes no further. 

Using driver version 1 for media type 2
Base ethernet MAC Address: 00:24:13:c4:64:80
Xmodem file system is available.
The password-recovery mechanism is enabled.

The system has been interrupted prior to initializing the
flash filesystem. The following commands will initialize
the flash filesystem, and finish loading the operating
system software:

flash_init
boot


switch: flash_init
Initializing Flash...
mifs[2]: 10 files, 1 directories
mifs[2]: Total bytes : 1835008
mifs[2]: Bytes used : 614400
mifs[2]: Bytes available : 1220608
mifs[2]: mifs fsck took 1 seconds.
mifs[3]: 0 files, 1 directories
mifs[3]: Total bytes : 3932160
mifs[3]: Bytes used : 1024
mifs[3]: Bytes available : 3931136
mifs[3]: mifs fsck took 0 seconds.
mifs[4]: 5 files, 1 directories
mifs[4]: Total bytes : 262144
mifs[4]: Bytes used : 9216
mifs[4]: Bytes available : 252928
mifs[4]: mifs fsck took 0 seconds.
mifs[5]: 5 files, 1 directories
mifs[5]: Total bytes : 262144
mifs[5]: Bytes used : 9216
mifs[5]: Bytes available : 252928
mifs[5]: mifs fsck took 0 seconds.
-- MORE --
mifs[6]: 5 files, 1 directories
mifs[6]: Total bytes : 57409536
mifs[6]: Bytes used : 14741504
mifs[6]: Bytes available : 42668032
mifs[6]: mifs fsck took 11 seconds.
...done Initializing Flash.

switch: boot
Loading "flash:c3750e-ipbasek9-mz.122-55.SE12.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:c3750e-ipbasek9-mz.122-55.SE12.bin" uncompressed and installed, entry point: 0x3000
executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

 

Cisco IOS Software, C3750E Software (C3750E-IPBASEK9-M), Version 12.2(55)SE12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Thu 28-Sep-17 01:02 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000

Initializing flashfs...
Using driver version 1 for media type 2
mifs[3]: 10 files, 1 directories
mifs[3]: Total bytes : 1835008
mifs[3]: Bytes used : 614400
mifs[3]: Bytes available : 1220608
mifs[3]: mifs fsck took 0 seconds.
mifs[3]: Initialization complete.

mifs[4]: 0 files, 1 directories
mifs[4]: Total bytes : 3932160
mifs[4]: Bytes used : 1024
mifs[4]: Bytes available : 3931136
mifs[4]: mifs fsck took 0 seconds.
mifs[4]: Initialization complete.

mifs[5]: 5 files, 1 directories
mifs[5]: Total bytes : 262144
mifs[5]: Bytes used : 9216
mifs[5]: Bytes available : 252928
mifs[5]: mifs fsck took 0 seconds.
mifs[5]: Initialization complete.

mifs[6]: 5 files, 1 directories
mifs[6]: Total bytes : 262144
mifs[6]: Bytes used : 9216
mifs[6]: Bytes available : 252928
mifs[6]: mifs fsck took 1 seconds.
mifs[6]: Initialization complete.

mifs[7]: 5 files, 1 directories
mifs[7]: Total bytes : 57409536
mifs[7]: Bytes used : 14741504
mifs[7]: Bytes available : 42668032
mifs[7]: mifs fsck took 0 seconds.
mifs[7]: Initialization complete.

...done Initializing flashfs.

Checking for Bootloader upgrade.. not needed
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed

POST: MA BIST : Begin
POST: MA BIST : End, Status Passed

POST: TCAM BIST : Begin
POST: TCAM BIST : End, Status Passed

POST: SF ASIC BIST : Begin
POST: SF ASIC BIST : End, Status Passed

POST: Switch Fabric Memory Tests : Begin
POST: Switch Fabric Memory Tests : End, Status Passed

POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed

POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed

extracting front_end/front_end_ucode_info (309 bytes)
Waiting for Stack Master Election...
POST: Thermal, Fan Tests : Begin
POST: Thermal, Fan Tests : End, Status Passed

POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed

POST: EMAC Loopback Tests : Begin
POST: EMAC Loopback Tests : End, Status Passed

Election Complete
Switch 1 booting as Master
Waiting for Port download...Complete


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco WS-C3750E-24TD (PowerPC405) processor (revision F0) with 262144K bytes of memory.
Processor board ID FDO1248R0YR
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
28 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:24:13:C4:64:80
Motherboard assembly number : 73-10313-11
Motherboard serial number : FDO12480DL9
Model revision number : F0
Motherboard revision number : A0
Model number : WS-C3750E-24TD-S
Daughterboard assembly number : 800-28590-01
Daughterboard serial number : FDO1248088T
System serial number : FDO1248R0YR
Top Assembly Part Number : 800-27546-03
Top Assembly Revision Number : A0
Version ID : V02
CLEI Code Number : COMSE00ARA
Hardware Board Revision Number : 0x01


Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 30 WS-C3750E-24TD 12.2(55)SE12 C3750E-IPBASEK9-M

 


Press RETURN to get started!


*Mar 1 00:00:25.828: Read env variable - LICENSE_BOOT_LEVEL =
*Mar 1 00:00:26.675: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c3750e Next reboot level = ipbase and License = ipbase
*Mar 1 00:01:28.751: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack
*Mar 1 00:01:31.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Mar 1 00:01:31.477: %SMI-5-CLIENT: Smart Install Client feature is enabled. It is recommended to disable the Smart Install feature when it is not actively used. To disable feature execute 'no vstack' in configuration mode
*Mar 1 00:01:32.803: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Mar 1 00:01:35.571: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:01:35 UTC Mon Mar 1 1993 to 16:01:35 PST Sun Feb 28 1993, configured from console by console.
*Mar 1 00:01:35.579: %SYS-6-CLOCKUPDATE: System clock has been updated from 16:01:35 PST Sun Feb 28 1993 to 16:01:35 PST Sun Feb 28 1993, configured from console by console.
*Mar 1 00:01:36.225: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan25, changed state to down
*Mar 1 00:01:36.452: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:01:36.812: %STACKMGR-5-SWITCH_READY: Switch 1 is READY
*Mar 1 00:01:36.812: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
*Mar 1 00:01:36.812: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
*Mar 1 00:01:37.425: %STACKMGR-5-MASTER_READY: Master Switch 1 is READY
*Mar 1 00:01:37.433: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3750E Software (C3750E-IPBASEK9-M), Version 12.2(55)SE12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Thu 28-Sep-17 01:02 by prod_rel_team
*Mar 1 00:01:37.458: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Mar 1 00:01:37.525: MKA-LLI: Failover Event
*Mar 1 00:01:39.421: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to down
*Mar 1 00:01:40.411: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan25, changed state to up
*Mar 1 00:01:40.436: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:01:42.391: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/23, changed state to up
*Mar 1 00:01:43.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/23, changed state to up
sw-rok2>

 


@electron_billeuze wrote:

If I simply boot without holding down the status button to enter ROMmon, I only get the first 4 lines of below and then it just hangs and goes no further. 


I have never seen a switch behave like this.  Can you share the config of the switch?

OK, Im sure the config has nothing to do with the boot issue because it hangs on boot before it even looks at the config. but, here is the config:

sw-rok2#show run
Building configuration...

Current configuration : 2836 bytes
!
! No configuration change since last restart
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname sw-rok2
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$AsnF$PmR.vhtfddzlkCRYGKwL50
!
username bill privilege 15 secret 5 $1$E8zz$ChpclmUVQweLmYvDwdFcW0
username bleuze privilege 15 secret 5 $1$1Qsu$Og0GJ/XQKpmxqCHkaa1Qs/
username admin privilege 15 secret 5 $1$5hH0$t6S5eZfaxxmaEVJDSGgqg.
!
!
no aaa new-model
clock timezone PST -8
clock summer-time PDT recurring
switch 1 provision ws-c3750e-24td
system mtu routing 1500
ip routing
!
!
no ip domain-lookup
ip domain-name colonial.local
ip host tftpd 10.0.25.56
ip host col-wsus1 10.0.25.56
vtp mode transparent
!
!
!
archive
path tftp://10.0.25.56/sw-rok2/$h-$t
write-memory
!
spanning-tree mode rapid-pvst
spanning-tree portfast default
spanning-tree portfast bpduguard default
spanning-tree extend system-id
!
!
!
errdisable recovery cause bpduguard
errdisable recovery interval 360
!
vlan internal allocation policy ascending
!
vlan 25
name CCV-Stone
!
!
!
interface FastEthernet0
no ip address
no ip route-cache cef
no ip route-cache
no ip mroute-cache
!
interface GigabitEthernet1/0/1
!
interface GigabitEthernet1/0/2
!
interface GigabitEthernet1/0/3
!
interface GigabitEthernet1/0/4
!
interface GigabitEthernet1/0/5
!
interface GigabitEthernet1/0/6
!
interface GigabitEthernet1/0/7
!
interface GigabitEthernet1/0/8
!
interface GigabitEthernet1/0/9
!
interface GigabitEthernet1/0/10
!
interface GigabitEthernet1/0/11
!
interface GigabitEthernet1/0/12
!
interface GigabitEthernet1/0/13
!
interface GigabitEthernet1/0/14
!
interface GigabitEthernet1/0/15
!
interface GigabitEthernet1/0/16
!
interface GigabitEthernet1/0/17
!
interface GigabitEthernet1/0/18
!
interface GigabitEthernet1/0/19
!
interface GigabitEthernet1/0/20
!
interface GigabitEthernet1/0/21
!
interface GigabitEthernet1/0/22
!
interface GigabitEthernet1/0/23
description rok users
switchport access vlan 25
switchport mode access
spanning-tree bpduguard disable
!
interface GigabitEthernet1/0/24
!
interface GigabitEthernet1/0/25
!
interface GigabitEthernet1/0/26
!
interface GigabitEthernet1/0/27
!
interface GigabitEthernet1/0/28
!
interface TenGigabitEthernet1/0/1
!
interface TenGigabitEthernet1/0/2
!
interface Vlan1
ip address 10.0.10.252 255.255.255.0
!
interface Vlan25
ip address 10.0.25.252 255.255.255.0
!
ip default-gateway 10.0.25.254
ip classless
ip route 0.0.0.0 0.0.0.0 10.0.25.254
no ip http server
no ip http secure-server
!
!
no vstack
!
line con 0
exec-timeout 0 0
logging synchronous
line vty 0 4
exec-timeout 120 0
login local
transport input all
line vty 5 15
exec-timeout 30 0
login local
transport input all
!
ntp clock-period 36029255
ntp server 10.0.25.55
end

Nothing wrong with the config.

Upgrade to 15.0(2)SE and see if gets improved.

That’s not a bad idea. I’ll try that Monday.

15.02 (2) made no difference. behavior is still the same.

One thing to note is that when I first changed the IOS from c3750e-universalk9-mz.122-50 to c3750e-ipbasek9-mz.122-55.SE12, I noticed this on the first boot once the new c3750e-ipbasek9-mz.122-55.SE12 loaded into memory, the first thing it did after initializing flashfs was:

Checking for Bootloader upgrade.. upgrading.. writing boot sectors..done.
The system will now restart

and then it tried  to restart and this was the fist time it failed to boot, the first time it got stuck and I had to enter ROMmon to get it started.

I was hoping your idea to install ios 15 would force it to do another "Bootloader upgrade" and fix the issue. But it didn't. Ever since this first Bootloader upgrade, what happens when it boots is exactly what it says: "system has been interrupted prior to initializing the flash filesystem". But why, and how to fix it?

 

 

I have now tried the following 2 extreme measures
-1) format flash: (followed by downloading an ios via xmodem)
-2) export the boostsector from a working switch, importing it to this one using the following procedure: https://community.cisco.com/t5/switching/3750x-bootloader/td-p/2502792 

No difference, still won't boot automatically.

I think I just have to consider this switch as bricked and save it for parts (power supply). I've already ordered another. 

 

amikat
Level 7
Level 7

Hi,

Your issue may be subject to Field Notice 63745 as per beneath:

https://www.cisco.com/c/en/us/support/docs/field-notices/637/fn63745.html?dtid=osscdc000283

Best regards,

Antonin

Hmm, interesting. Although the symptoms described are not exactly as observed in my case, If indeed this is the issue it just confirms my latest theory that the switch is bricked.

Review Cisco Networking for a $25 gift card