08-28-2022 12:31 AM - edited 08-28-2022 12:32 AM
Hi,
below L3 model will supporting MPLS/VPLS
Model WS-C3850-48XS
SW Version 16.12.07
flash:cat3k_caa-universalk9ldpe.16.12.07.SPA.bin"
Solved! Go to Solution.
08-28-2022 03:23 AM
You need IP services license for this switch to enable MPLS and VPLS
https://cfnng.cisco.com/browse/switching/products
08-28-2022 02:26 AM - edited 08-28-2022 02:27 AM
Not sure what feature of MPLS/VPLS you looking for, This is more of the Switch, depends on the License and some features of MPLS/VPLS to support.
cat3k_caa-universalk9ldpe.16.12.07.SPA.bin ( this image is CAT3850/3650 UNIVERSAL W/O DTLS)
if you looking for universal :cat3k_caa-universalk9.16.12.07.SPA.bin
08-28-2022 02:51 AM
not able to enable basic MPLS and VPLS with cat3k_caa-universalk9ldpe.16.12.07.SPA.bin IOS....
if i replace with cat3k_caa-universalk9.16.12.07.SPA.bin, MPLS/VPLS feature will enable..?
08-28-2022 05:24 AM
show run and show license will show you what License you have.
any advanced features MPLS/VPLS or any VRF required IPService License.
08-28-2022 03:23 AM
You need IP services license for this switch to enable MPLS and VPLS
https://cfnng.cisco.com/browse/switching/products
08-28-2022 03:35 AM
i will try to load universalk9.16.12.07 IOS
Thank you for your information.
08-28-2022 03:59 AM
Hi,
i am not able to replace exiting IOS image, and getting below error message.
Logs:-
Switch(config)#boot system flash:?
flash:.dbpersist
flash:.installer
flash:.prst_sync
flash:.rollback_timer
flash:boothelper.log
flash:boothelper.old
flash:bootloader_evt_handle.log
flash:cat3k_caa-universalk9.16.06.01.SPA.bin
flash:cat3k_caa-universalk9.16.12.07.SPA.bin
flash:cat3k_caa-universalk9ldpe.16.12.07.SPA.bin
flash:core
flash:dc_profile_dir
Switch#wr memory
% FACTORYRESET - Exiting without calling factory_reset
watchdog: watchdog0: watchdog did not stop!
reboot: Restarting system
Booting...(use DDR clock 667 MHz)
Interface GE 0 link down***ERROR: PHY link is down
The "IP_ADDR" environment variable is not set.
Reading full image into memory.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................done
Bundle Image
--------------------------------------
Kernel Address : 0x537766ec
Kernel Size : 0x4381df/4424159
Initramfs Address : 0x53bae8cb
Initramfs Size : 0x1ab6104/28008708
Compression Format: mzip
Bootable image at @ ram:0x537766ec
Bootable image segment 0 address range [0x81100000, 0x81da5280] is in range [0x80180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:cat3k_caa-universalk9ldpe.16.12.07.SPA.bin" uncompressed and installed, entry point: 0x81895bf0
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide