10-19-2016 02:21 AM - edited 03-08-2019 07:50 AM
Hello
I am trying to install C6800-32P-10G Ethernet fiber module into Cisco 6807-XL switch.
As per datasheet, module can be connected into slot 1-2 or 5-7 in 6807-XL. I installed module into slot 2 but its showing powerdown.
"Can occupy slots 1-2 and 5-7 in a Cisco Catalyst 6807-XL."
GP-CORE1#show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6848-GE-TX SAL1949UCE9
2 40 FRU type (0x6003, 0x57E(1406)) C6800-32P10G SAL1951V8J0
3 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1940Q4TE
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 cc46.d693.2064 to cc46.d693.2093 1.4 12.2(18r)S1 15.1(2)SY6 Ok
2 ecbd.1d8c.82b4 to ecbd.1d8c.82db 1.1 Unknown Unknown PwrDown
3 d072.dcbb.dc3e to d072.dcbb.dc45 2.1 12.2(50r)SYS 15.1(2)SY6 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6K-DFC4-A SAL1949UCE9 1.4 Ok
3 Policy Feature Card 4 VS-F6K-PFC4 SAL1951VHA1 3.0 Ok
3 CPU Daughterboard VS-F6K-MSFC5 SAL1951VDNZ 3.1 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Not Applicable
3 Pass
GP-CORE1#
*Oct 19 09:16:39.439: %C6KPWR-SW1-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type.
show version:
GP-CORE1#show version
Cisco IOS Software, s2t54 Software (s2t54-IPBASEK9-M), Version 15.1(2)SY6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Thu 10-Sep-15 01:36 by prod_rel_team
ROM: System Bootstrap, Version 12.2(50r)SYS3, RELEASE SOFTWARE (fc1)
Any suggestion ?
Regards
Solved! Go to Solution.
10-19-2016 02:48 AM
Hello
The datasheet below states the minimum ios version for supporting these modules is 15.2(1)SY.
hth
Andy
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6800-series-switches/datasheet-c78-733662.html
10-19-2016 02:48 AM
Version 15.1(2)SY6
Upgrade the IOS of the chassis to a minimum level of 15.2(1)SY. This fact is stated in the Data Sheet (Table 1).
10-19-2016 02:48 AM
Hello
The datasheet below states the minimum ios version for supporting these modules is 15.2(1)SY.
hth
Andy
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6800-series-switches/datasheet-c78-733662.html
10-19-2016 02:58 AM
Thank you so much for quick reply.
Can i direct upgrade from 15.1(2)SY6 to 15.4 ?
Regards
10-19-2016 03:22 AM
Yes.
Don't forget to read the Release Notes.
10-19-2016 03:34 AM
Upgrade done. Module detected.
Thanks for help
10-19-2016 02:48 AM
Version 15.1(2)SY6
Upgrade the IOS of the chassis to a minimum level of 15.2(1)SY. This fact is stated in the Data Sheet (Table 1).
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide