ā01-04-2023 12:14 AM
Hi all. I am beginner in Cisco. I have a problem. I have switches C9200-48P-E in stack 4. In one switch i have module C9200-NM-4X. It is connected with other switch in stack cisco. But on this module C9200-NM-4X when run command show interface status it show me that port Te1/1/1 is unknown Te1/1/1 Swiatlo notconnect 1 full 10G unknown
. Why ? On other switch with which i want connect show me Te4/0/1 Swiatlo notconnect 1 full 10G SFP-10GBase-SR
Can anybody help me step by step how connect two stack switches by fibre. Please i am beginner. Thanks
ā01-04-2023 01:09 AM
- Use compatible SFP(s) as mentioned in this list : https://tmgmatrix.cisco.com/?npid=1766
M.
ā01-04-2023 02:00 AM
I use compatible CISCO SFP-10GBase-SR
ā01-04-2023 01:17 AM
what is the IOS XE code running on Both the switches.
is this SFP Module you looking to use is Cisco or any 3rd party ?
can you post show inventor working and not working
post complete output of show interface ten 1/1/1 and show interface ten1/1/1 trans
ā01-04-2023 02:08 AM - edited ā01-04-2023 02:14 AM
On switch where SFP is reconized is ok i use version 15.0
On C9200-48P-E where in module C9200-NM-4X is show SFP as unknown i use version 16.12
On both switches i use the same gibic CISCO SFP-10GBase-SR
Inteface with ok reconized:
PD_xxxxxxxxxx_s-2#show interface tenGigabitEthernet 4/0/1
TenGigabitEthernet4/0/1 is down, line protocol is down (notconnect)
Hardware is Ten Gigabit Ethernet, address is 08d0.9f89.96b3 (bia 08d0.9f89.96b3)
Description: Swiatlo do PD_xxxxxxxxxxxx_Stak 3 Potry 1/1/1
MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 9 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
PD_xxxxxxxx_s-2#
Inteface where is unknown
PD_xxxxxxxxxx_s-3#show interface tenGigabitEthernet 1/1/1
TenGigabitEthernet1/1/1 is down, line protocol is down (notconnect)
Hardware is Ten Gigabit Ethernet, address is 40f0.7806.8035 (bia 40f0.7806.8035)
Description: Swiatlo do PD_xxxxxxxxxx_Stak 2 Potry 4/0/1
MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is unknown
input flow-control is on, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Class-based queueing
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
Output 0 broadcasts (0 multicasts)
0 output errors, 0 collisions, 3 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
PD_xxxxxxxxx_s-3#
When try command: show interface tenGigabitEthernet 1/1/1 trans i get info:
Diagnostic Monitoring is not implemented.
ā01-04-2023 03:26 AM
>...Diagnostic Monitoring is not implemented.
Probably a bug similar to https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuw98441 , use latest advisory software release on the 9200 and check if that can help : https://software.cisco.com/download/home/286320185/type/282046477/release/Bengaluru-17.6.4
M.
ā01-04-2023 05:55 AM
On C9200-48P-E where in module C9200-NM-4X is show SFP as unknown i use version 16.12
Upgrade code to 17.6.4 and test it.
ā01-04-2023 06:00 AM
But how i can update software with save configuration of switches ? I have in stack 4 switches(devices). Sorry i am beginner and i need help step by step. Thanks. And which software i must update on my switches ? CAT9200 UNIVERSAL or CAT9200 UNIVERSAL - NO PAYLOAD ENCRYPTION ?
And realese Bengaluru is correct for me ? I am from Poland. How i can check what version no i have installed ?
ā01-04-2023 04:05 AM - edited ā01-04-2023 04:06 AM
But how i can update software with save configuration of switches ? I have in stack 4 switches(devices). Sorry i am beginner and i need help step by step. Thanks. And which software i must update on my switches ? CAT9200 UNIVERSAL or CAT9200 UNIVERSAL - NO PAYLOAD ENCRYPTION ?
ā01-04-2023 06:04 AM
Can you post show version.are you using bundle are install mode
bundle mode means you running switch stack with .bin file
if boot have packages.conf - means install mode
Look below upgrade guide (in detailed)
ā01-04-2023 06:10 AM
@balaji.bandi wrote:Can you post show version.are you using bundle are install mode
bundle mode means you running switch stack with .bin file
if boot have packages.conf - means install mode
But how i can checkt it ?
ā01-04-2023 06:12 AM
If you closly look our reply you will find the answer post show version.are you using bundle are install mode
check #show boot
bundle mode means you running switch stack with .bin file
if boot have packages.conf - means install mode
ā01-04-2023 06:23 AM
PD_xxxxxxxxxxx_s-3#show version
Cisco IOS XE Software, Version 16.12.03a
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT9K_LITE_IOSXE), Version 16.12.3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 28-Apr-20 09:18 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2020 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: System Bootstrap, Version 17.3.1r [FC3], RELEASE SOFTWARE (P)
PD_Narutowicza_s-3 uptime is 4 weeks, 6 days, 7 hours, 28 minutes
Uptime for this control processor is 4 weeks, 6 days, 7 hours, 30 minutes
System returned to ROM by Power Failure or Unknown at 10:51:59 UTC Fri Sep 30 2022
System restarted at 06:52:31 UTC Thu Dec 1 2022
System image file is "flash:packages.conf"
Last reload reason: Power Failure or Unknown
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
------------------------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------------
network-essentials Smart License network-essentials
dna-essentials Subscription Smart License dna-essentials
Smart Licensing Status: UNREGISTERED/EVAL EXPIRED
cisco C9200-48P (ARM64) processor with 649168K/3071K bytes of memory.
Processor board ID JAE24421JBV
2 Virtual Ethernet interfaces
312 Gigabit Ethernet interfaces
24 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4060240K bytes of physical memory.
819200K bytes of Crash Files at crashinfo:.
819200K bytes of Crash Files at crashinfo-1:.
819200K bytes of Crash Files at crashinfo-2:.
819200K bytes of Crash Files at crashinfo-4:.
1941504K bytes of Flash at flash:.
1941504K bytes of Flash at flash-1:.
1941504K bytes of Flash at flash-2:.
1941504K bytes of Flash at flash-4:.
0K bytes of WebUI ODM Files at webui:.
Base Ethernet MAC Address : 40:f0:78:06:8b:00
Motherboard Assembly Number : 73-18791-04
Motherboard Serial Number : JAE24421JBV
Model Revision Number : C1
Motherboard Revision Number : B0
Model Number : C9200-48P
System Serial Number : JAE24421JBV
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
1 56 C9200-48P 16.12.3a CAT9K_LITE_IOSXE INSTALL
2 56 C9200-48P 16.12.3a CAT9K_LITE_IOSXE INSTALL
* 3 56 C9200-48P 16.12.3a CAT9K_LITE_IOSXE INSTALL
4 56 C9200-48P 16.12.3a CAT9K_LITE_IOSXE INSTALL
Switch 01
---------
Switch uptime : 4 weeks, 6 days, 7 hours, 31 minutes
Base Ethernet MAC Address : 40:f0:78:06:80:00
Motherboard Assembly Number : 73-18791-04
Motherboard Serial Number : JAE24421G9Y
Model Revision Number : C1
Motherboard Revision Number : B0
Model Number : C9200-48P
System Serial Number : JAE24421G9Y
Last reload reason : lost both active and standby
Switch 02
---------
Switch uptime : 4 weeks, 6 days, 7 hours, 31 minutes
Base Ethernet MAC Address : dc:77:4c:a7:5a:80
Motherboard Assembly Number : 73-18791-04
Motherboard Serial Number : JAE24421GCW
Model Revision Number : C1
Motherboard Revision Number : B0
Model Number : C9200-48P
System Serial Number : JAE24421GCW
Last reload reason : lost both active and standby
Switch 04
---------
Switch uptime : 4 weeks, 6 days, 7 hours, 31 minutes
Base Ethernet MAC Address : dc:77:4c:ea:d1:00
Motherboard Assembly Number : 73-18791-04
Motherboard Serial Number : JAE24421FFG
Model Revision Number : C1
Motherboard Revision Number : B0
Model Number : C9200-48P
System Serial Number : JAE24421FFG
Last reload reason : Power Failure or Unknown
Configuration register is 0x102
PD_xxxxxxxxxx_s-3#show boot
---------------------------
Switch 3
---------------------------
Current Boot Variables:
BOOT variable does not exist
Boot Variables on next reload:
BOOT variable = flash:packages.conf;
Manual Boot = no
Enable Break = no
Boot Mode = DEVICE
iPXE Timeout = 0
ā01-04-2023 07:04 AM
As per the output it is install mode, so you can use archive install as mentioned in the document.
I want to bring another information for your notice, looks like Switch 3 as acting as master now.
if you like to make the stack stream line Sw1 to be master, Sw2 prospect master and other members, setup correctly with switch number and priority
show switch give you what switch has what number and priority.
ā01-04-2023 11:03 AM
What you mean ? And can you tel me how change it to setup as master SW1 because in SW1 is installed module C9200-NM-4X and connect by sfp with other stack.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide